 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| enhanced a/d type 8-bit otp mcu HT46R068B/ht46r069b revision: 1.00 date: ?an?a?? ??? ? 011 ?an?a?? ??? ? 011
HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ? ?an?a?? ??? ? 011 rev. 1.00 3 ?an?a?? ??? ? 011 table of contents eates cpu feat??es ...................................................................................................................... 1 pe?iphe?al feat??es .............................................................................................................. 1 gene?al desc?iption ...................................................................................................... ? selection table .............................................................................................................. ? block diag?am ............................................................................................................... ? pin assignment ............................................................................................................. 3 pin desc?iption .............................................................................................................. 5 absol?te maxim?m ratings ......................................................................................... 7 d.c. cha?acte?istics ...................................................................................................... 7 a.c. cha?acte?istics ...................................................................................................... 9 adc cha?acte?istics .................................................................................................... 10 dac elect?ical cha?acte?istics ................................................................................... 10 powe?-on reset cha?acte?istics ................................................................................ 10 s?stem a?chitect??e .................................................................................................... 11 clocking and pipelining ...................................................................................................... 11 p?og?am co?nte? ................................................................................................................ 1? stack .................................................................................................................................. 13 a? ithmetic and logic unit C alu ........................................................................................ 13 p?og?am memo?? ......................................................................................................... 14 st??ct??e ............................................................................................................................. 14 special vecto ?s .................................................................................................................. 15 look-? p table ..................................................................................................................... 15 table p ?og?am example ..................................................................................................... 1? data memo?? ................................................................................................................ 18 st??ct??e ............................................................................................................................. 18 special p??pose data memo?? .......................................................................................... 19 special f?nction registe?s ........................................................................................ ?0 indi? ect add?essing registe?s C iar0? iar1 ...................................................................... ?0 memo?? pointe?s C mp0? mp1 ........................................................................................... ?0 acc?m?lato? C acc ............................................................................................................ ?3 p?og?am co?nte? low registe? C pcl ............................................................................... ?3 bank pointe? C bp .............................................................................................................. ?3 stat?s registe? C status ................................................................................................. ?4 inp?t/o?tp?t po?ts and cont?ol registe?s .......................................................................... ?5 s?stem cont?ol registe?s C ctrl0? ctrl1? ctrl? ........................................................ ?? wake- ?p f?nction registe? C pawk .................................................................................. ?8 p?ll-high registe? s C papu? pbpu? pcpu? pdpu? pepu? pfpu .................................... ?8 softwa?e com registe? C scomc .................................................................................... ?8 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ? ?an?a?? ??? ? 011 rev. 1.00 3 ?an?a?? ??? ? 011 oscillator ...................................................................................................................... 28 s?stem oscillato? ove?view ............................................................................................... ?8 exte?nal c??stal/resonato? oscillato? C hxt ..................................................................... ?8 exte?nal rc oscillato? C erc ............................................................................................ ?9 inte?nal rc oscillato? C hirc ............................................................................................ 30 exte?nal 3?7?8hz c??stal oscillato? C lxt ........................................................................ 30 lxt oscillato ? low powe? f?nction ................................................................................... 31 inte?nal low speed oscillato? C lirc ................................................................................ 31 operating modes ......................................................................................................... 32 mode t ?pes and selection ................................................................................................. 3? mode switching .................................................................................................................. 33 standb? c???ent conside?ations ........................................................................................ 33 wake- ?p ............................................................................................................................. 34 watchdog time ? ope?ation ................................................................................................ 35 reset and initialisation ............................................................................................... 36 reset f?nctions ................................................................................................................. 37 reset initial conditions ...................................................................................................... 39 input/output ports ....................................................................................................... 41 p?ll-high resisto?s ............................................................................................................. 41 po? t a wake-?p .................................................................................................................. 41 i/o po?t cont?ol registe?s .................................................................................................. 43 pin-sha?ed f?nctions ......................................................................................................... 44 pin remapping confguration ............................................................................................ 45 i/o pin st??ct??es ............................................................................................................... 45 p?og?amming conside?ations ............................................................................................. 47 timer/event counters ................................................................................................. 47 confguring the timer/event counter input clock source ................................................. 47 time ? registe? s C tmr0? tmr1? tmr?l? tmr?h ............................................................ 48 time ? cont? ol registe? s C tmr0c? tmr1c? tmr?c ........................................................ 48 time ? mode ........................................................................................................................ 5? event co?nte? mode .......................................................................................................... 5? p?lse width capt??e mode ................................................................................................ 53 p?escale? ............................................................................................................................ 54 pfd f?nction ..................................................................................................................... 54 i/o inte?facing ..................................................................................................................... 55 p?og?amming conside?ations ............................................................................................. 55 time ? p?og?am example .................................................................................................... 5? time base .......................................................................................................................... 5? pulse width modulator ............................................................................................... 57 pwm ope?ation .................................................................................................................. 58 ?+? pwm mode ................................................................................................................. 58 7+1 pwm mode ................................................................................................................. 59 pwm o?tp?t cont?ol .......................................................................................................... ?0 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 4 ?an?a?? ??? ? 011 rev. 1.00 5 ?an?a?? ??? ? 011 analog to digital converter ........................................................................................ 61 a/d ove?view ..................................................................................................................... ?1 a/d conve?te? data registe? s C adrl? adrh .................................................................. ?1 a/d conve ?te? cont? ol registe? s C adcr? acsr? ancsr1? ancsr0 ............................. ?1 a/d inp?t pins .................................................................................................................... ?7 s?mma?? of a/d conve?sion steps .................................................................................... ?7 p?og?amming conside?ations ............................................................................................. ?8 a/d t ?ansfe? f?nction ........................................................................................................ ?8 a/d p?og?amming example ................................................................................................ ?9 interrupts ...................................................................................................................... 72 inte???pt registe? ............................................................................................................... 7? inte???pt ope?ation ............................................................................................................. 74 inte???pt p?io?it? .................................................................................................................. 75 exte?nal inte???pt ................................................................................................................ 7? time ?/event co?nte? inte???pt ............................................................................................ 7? m?lti-f?nction inte???pt ....................................................................................................... 7? p?og?amming conside?ations ............................................................................................. 77 lcd scom function ................................................................................................... 78 lcd ope?ation .................................................................................................................. 78 lcd bias cont?ol ............................................................................................................... 79 serial interface module C sim ..................................................................................... 80 spi inte?face ...................................................................................................................... 80 spi registe?s ..................................................................................................................... 8? spi comm?nication .......................................................................................................... 85 i ? c inte?face ....................................................................................................................... 87 i ? c registe?s ...................................................................................................................... 88 i ? c b?s comm?nication ..................................................................................................... 9? i ? c b?s sta?t signal ............................................................................................................ 93 slave add?ess .................................................................................................................... 93 i ? c b?s read/w ?ite signal ................................................................................................. 94 i ? c b? s slave add? ess acknowledge signal ...................................................................... 94 i ? c b? s data and acknowledge signal .............................................................................. 94 peripheral clock output ............................................................................................. 97 pe?iphe?al clock ope?ation ................................................................................................ 97 spia serial interface C spia ....................................................................................... 98 spia inte ?face comm?nication .......................................................................................... 98 spia registe ?s ................................................................................................................... 98 spia b ?s enable/disable ................................................................................................... 98 spia ope ?ation ................................................................................................................ 100 spia confguration options ............................................................................................. 10? e??o? detection ................................................................................................................. 10? p?og?amming conside?ations ........................................................................................... 10? digital to analog converter C dac ......................................................................... 102 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 4 ?an?a?? ??? ? 011 rev. 1.00 5 ?an?a?? ??? ? 011 ope?ation ......................................................................................................................... 10? low voltage detector - lvd ...................................................................................... 103 lvd registe ? .................................................................................................................... 103 lvd ope ?ation ................................................................................................................. 104 confguration options .............................................................................................. 104 application circuit .................................................................................................... 106 instruction set ........................................................................................................... 107 int?od?ction ...................................................................................................................... 107 inst?? ction timing ............................................................................................................. 107 moving and t ?ansfe??ing data .......................................................................................... 107 a?ithmetic ope?ations ....................................................................................................... 107 logical and rotate ope?ations ......................................................................................... 107 b?anches and cont? ol t ?ansfe? ........................................................................................ 108 bit ope?ations .................................................................................................................. 108 table read ope ?ations .................................................................................................... 108 othe? ope?ations .............................................................................................................. 108 instruction set summary .......................................................................................... 109 table conventions ............................................................................................................ 109 instruction defnition ................................................................................................. 111 package information ................................................................................................. 121 ? 8-pin skdip (300mil) o?tline dimensions ..................................................................... 1?1 ? 8-pin sop (300mil) o?tline dimensions ........................................................................ 1?? ? 8-pin ssop (150mil) o?tline dimensions ...................................................................... 1?3 44-pin qfp (10mmx10mm) o ?tline dimensions ............................................................. 1?4 5? -pin qfp (14mmx14mm) o?tline dimensions ............................................................. 1?5 ? 4-pin lqfp (7mmx7mm) o?tline dimensions ............................................................... 1?? reel dimensions .............................................................................................................. 1?7 ca??ie? tape dimensions .................................................................................................. 1?8 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 pb ?an?a?? ??? ? 011 rev. 1.00 1 ?an?a?? ??? ? 011 features cpu features operating voltage: f sys = 4mhz: 2.2v~5.5v f sys =8mhz: 3.0v~5.5v f sys =12mhz: 4.5v~5.5v up to 0.33s instruction cycle with 12mhz system clock at v dd = 5v idle/sleep mode and wake-up functions to reduce power consumption oscillator types: external high frequency crystal C hxt external rc C erc internal rc C hirc external low frequency crystal C lxt four operational modes: normal, slow, idle, sleep fully integrated internal 4mhz, 8mhz and 12mhz oscillator requires no external components watchdog timer function lirc oscillator function for watchdog timer all instructions executed in one or two instruction cycles table read instructions 63 powerful instructions up to 8-level subroutine nesting bit manipulation instruction low voltage reset function low voltage detect function wide range of available package types peripheral features up to 62 bidirectional i/o lines up to 16 channel 12-bit adc up to 4 channel 8-bit pwm single channel 12-bit dac serial interfaces module with dual spi and i 2 c interfaces single serial spi interface software controlled 4-scom lines lcd com driver with 1/2 bias external interrupt input shared with an i/o line t wo 8-bit programmable timer/event counter with overfow interrupt and prescaler single 16-bit programmable timer/event counter with overfow interrupt time-base function programmable frequency divider C pfd HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ? ?an?a?? ??? ? 011 rev. 1.00 3 ?an?a?? ??? ? 011 general description the enhanced a/d mcus are a series of 8-bit high performance, risc architecture microcontrollers specifcally designed for a wide range of applications. the usual holtek microcontroller features of low power consumption, i/o fexibility, timer functions, oscillator options, power down and wake- up functions, watchdog timer and low voltage reset, combine to provide devices with a huge range of functional options while still maintaining a high level of cost effectiveness. the fully integrated system oscillator hirc, which requires no external components and which has three frequency selections, opens up a huge range of new application possibilities for these devices, some of which may include industrial control, consumer products, household appliances subsystem controllers, etc. selection table part no. program memory data memory i/o 8-bit timer 16-bit timer time base hirc (mhz) rtc (lxt) lcd scom ht4?r0?8b 1?kx1? 51?x8 50 ? 1 1 4/8/1? (*) 4 ht4?r0?9b 3?kx1? 10?4x8 ?? ? 1 1 4/8/1? (*) 4 part no. a/d pwm d/a interface pfd stack package ht4?r0?8b 1?-bitx1? 8-bitx4 1?-bitx1 spi/i ? c? spi 8 ?8skdip/ sop/ssop ? 44/5?qfp ht4?r0?9b 1?-bitx1? 8-bitx4 1?-bitx1 spi/i ? c? spi 8 44/5?qfp ?4lqfp note: "*" the oscillator is connected to the xt1/xt2 pins with tinypower tm design. block diagram the following block diagram illustrates the main functional blocks. ? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ? ?an?a?? ??? ? 011 rev. 1.00 3 ?an?a?? ??? ? 011 pin assignment pa4/pwm0/tc1/aud pa3/int/an3 pa ?/tc0/an?/vref pa1/pfd/an1 pa0/an0 pc?/an? pc7/an7 pc0/an4 pc1/an5 pd0/tc? pd1/pwm3 pb0/scom0 pb1/scom1 pb?/scom? HT46R068B 28 ssop-a/sop-a/skdip-a vss vdd pa5/osc ? pa ?/osc1 pc5/xt1 pc4/xt? pa7/ res pc3/pwm1 pc?/pwm? pd3/pck pd? pb5 pb4 pb3/scom3 1 ? 3 4 5 ? 7 8 9 10 11 1? 13 14 ?8 ?7 ?? ?5 ?4 ?3 ?? ?1 ?0 19 18 17 1? 15 HT46R068B 44 qfp-a 44 43 4? 41 40 39 38 37 3? 35 34 1? 13 14 15 1? 17 18 19 ?0 ?1 ?? 1 ? 3 4 5 ? 7 8 9 10 11 pc7/an7 pc0/an4 pc1/an5 pe0/an8 pe1/an9 pe?/an10 pe3/an11 pe4/an1? pe5/an13 pe?/an14 pe7/an15 33 3? 31 30 ?9 ?8 ?7 ?? ?5 ?4 ?3 pc4/xt? pa7/ res pc3/pwm1 pc?/pwm? pd7/sdo pd?/sdi/sda pd5/sck/scl pd4/scs pd3/pclk pd? pf1/sdia pf0/sdoa pb7/scka pb?/scsa pb5 pb4 pb3/scom3 pb?/scom? pb1/scom1 pb0/scom0 pd1/pwm3 pd0/tc? pc5/xt1 pa ?/osc1 pa5/osc ? vdd vss pa4/pwm0/tc1/aud pa3/int/an3 pa ?/tc0/an?/vref pa1/pfd/an1 pa0/an0 pc?/an? HT46R068B 52 qfp-a 1 ? 3 4 5 ? 7 8 9 10 11 1? 13 pc1/an5 pe0/an8 pe1/an9 pe?/an10 pe3/an11 pe4/an1? pe5/an13 pe?/an14 pe7/an15 pg0 pg1 pd0/tc? pd1/pwm3 39 38 37 3? 35 34 33 3? 31 30 ?9 ?8 ?7 pc4/xt? pa7/ res pc3/pwm1 pc?/pwm? pd7/sdo pd?/sdi/sda pd5/sck/scl pd4/scs pd3/pclk pd? pf7 pf? pf5 14 15 1? 17 18 19 ?0 ?1 ?? ?3 ?4 ?5 ?? pf4 pf3 pf? pf1/sdia pf0/sdoa pb7/scka pb?/scsa pb5 pb4 pb3/scom3 pb?/scom? pb1/scom1 pb0/scom0 5? 51 50 49 48 47 4? 45 44 43 4? 41 40 pc5/xt1 pa ?/osc1 pa5/osc ? vdd vss pa4/pwm0/tc1/aud pa3/int/an3 pa ?/tc0/an?/vref pa1/pfd/an1 pa0/an0 pc?/an? pc7/an7 pc0/an4 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 4 ?an?a?? ??? ? 011 rev. 1.00 5 ?an?a?? ??? ? 011 ht46r069b 44 qfp-a 44 43 4? 41 40 39 38 37 3? 35 34 1? 13 14 15 1? 17 18 19 ?0 ?1 ?? 1 ? 3 4 5 ? 7 8 9 10 11 pc7/an7 pc0/an4 pc1/an5 pe0/an8 pe1/an9 pe?/an10 pe3/an11 pe4/an1? pe5/an13 pe?/an14 pe7/an15 33 3? 31 30 ?9 ?8 ?7 ?? ?5 ?4 ?3 pc4/xt? pa7/ res pc3/pwm1 pc?/pwm? pd7/sdo pd?/sdi/sda pd5/sck/scl pd4/scs pd3/pclk pd? pf1/sdia pf0/sdoa pb7/scka pb?/scsa pb5 pb4 pb3/scom3 pb?/scom? pb1/scom1 pb0/scom0 pd1/pwm3 pd0/tc? pc5/xt1 pa ?/osc1 pa5/osc ? vdd vss pa4/pwm0/tc1/aud pa3/int/an3 pa ?/tc0/an?/vref pa1/pfd/an1 pa0/an0 pc?/an? ht46r069b 52 qfp-a 1 ? 3 4 5 ? 7 8 9 10 11 1? 13 pc1/an5 pe0/an8 pe1/an9 pe?/an10 pe3/an11 pe4/an1? pe5/an13 pe?/an14 pe7/an15 pg0 pg1 pd0/tc? pd1/pwm3 39 38 37 3? 35 34 33 3? 31 30 ?9 ?8 ?7 pc4/xt? pa7/ res pc3/pwm1 pc?/pwm? pd7/sdo pd?/sdi/sda pd5/sck/scl pd4/scs pd3/pclk pd? pf7 pf? pf5 14 15 1? 17 18 19 ?0 ?1 ?? ?3 ?4 ?5 ?? pf4 pf3 pf? pf1/sdia pf0/sdoa pb7/scka pb?/scsa pb5 pb4 pb3/scom3 pb?/scom? pb1/scom1 pb0/scom0 5? 51 50 49 48 47 4? 45 44 43 4? 41 40 pc5/xt1 pa ?/osc1 pa5/osc ? vdd vss pa4/pwm0/tc1/aud pa3/int/an3 pa ?/tc0/an?/vref pa1/pfd/an1 pa0/an0 pc?/an? pc7/an7 pc0/an4 ht46r069b 64 qfp-a 1 ? 3 4 5 ? 7 8 9 10 11 1? 13 14 15 1? pc1/an5 pe0/an8 pe1/an9 pe?/an10 pe3/an11 pe4/an1? pe5/an13 pe?/an14 pe7/an15 pg0 pg1 pg? pg3 pg4 pg5 pg? 48 47 4? 45 44 43 4? 41 40 39 38 37 3? 35 34 33 17 18 19 ?0 ?1 ?? ?3 ?4 ?5 ?? ?7 ?8 ?9 30 31 3? pf4 pf3 pf? pf1/sdia pf0/sdoa pb7/scka pb?/scsa pb5 pb4 pb3/scom3 pb?/scom? pb1/scom1 pb0/scom0 pd1/pwm3 pd0/tc? pg7 ?4 ?3 ?? ?1 ?0 59 58 57 5? 55 54 53 5? 51 50 49 pc3/pwm1 pa7/ res pc4/xt? pc5/xt1 pa ?/osc1 pa5/osc ? vdd vss pa4/pwm0/tc1/aud pa3/int/an3 pa ?/tc0/an?/vref pa1/pfd/an1 pa0/an0 pc?/an? pc7/an7 pc0/an4 pc?/pwm? pd7/sdo pd?/sdi/sda pd5/sck/scl pd4/scs pd3/pclk pd? ph5 ph4 ph3 ph? ph1 ph0 pf7 pf? pf5 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 4 ?an?a?? ??? ? 011 rev. 1.00 5 ?an?a?? ??? ? 011 pin description pin name function opt i/t o/t descriptions pa0/an0 pa0 papu pawk st cmos gene?al p??pose i/o. registe? enabled p?ll-?p and wake-?p. an0 ancsr0 an a/d channel 0 pa1/pfd/an1 pa1 papu pawk st cmos gene?al p??pose i/o. registe? enabled p?ll-?p and wake-?p. pfd ctrl0 cmos pfd o?tp?t an1 ancsr0 an a/d channel 1 pa ?/tc0/an?/vref pa ? papu pawk st cmos gene?al p??pose i/o. registe? enabled p?ll-?p and wake-?p. tc0 st exte? nal time? 0 clock inp?t an? ancsr0 an a/d channel ? vref acsr an adc ?efe?ence inp?t pa3/intb/an3 pa3 papu pawk st cmos gene?al p??pose i/o. registe? enabled p?ll-?p and wake-?p. intb st exte?nal inte???pt inp?t an3 ancsr0 an a/d channel 3 pa4/pwm0/tc1/aud pa4 papu pawk st cmos gene?al p??pose i/o. registe? enabled p?ll-?p and wake-?p. pwm0 ctrl0 cmos pwm o?tp?t tc1 st exte? nal time? 1 clock inp?t aud an dac o?tp?t pa5/osc ? pa5 papu pawk st cmos gene?al p??pose i/o. registe? enabled p?ll-?p and wake-?p. osc? co osc oscillato? pin pa ?/osc1 pa ? papu pawk st cmos gene?al p??pose i/o. registe? enabled p?ll-?p and wake-?p. osc1 co osc oscillato? pin pa7/ res pa7 pawk st nmos gene?al p??pose i/o. registe? enabled wake-?p. res co st reset inp?t pb0/scom0 pb0 pbpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p scom0 scomc scom softwa?e cont?olled 1/? bias lcd com pb1/scom1 pb1 pbpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p scom1 scomc scom softwa?e cont?olled 1/? bias lcd com pb?/scom? pb? pbpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p scom? scomc scom softwa?e cont?olled 1/? bias lcd com pb3/scom3 pb3 pbpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p scom3 scomc scom softwa?e cont?olled 1/? bias lcd com pb4?pb5 pb4?pb5 pbpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p pb?/ scsa pb? pbpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p scsa st spi slave select pb7/scka pb7 pbpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p scka st cmos spi se?ial clock pc0/an4 pc0 pcpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p. an4 ancsr0 an a/d channel 4 pc1/an5 pc1 pcpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p. an5 ancsr0 an a/d channel 5 pc?/pwm? pc? pcpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p. pwm? ctrl? cmos pwm o?tp?t pc3/pwm1 pc3 pcpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p. pwm1 ctrl0 cmos pwm o?tp?t pc4/xt? pc4 pcpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p. xt? co lxt low f?eq?enc? c??stal pin pc5/xt1 pc5 pcpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p. xt1 co lxt low f?eq?enc? c??stal pin HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ? ?an?a?? ??? ? 011 rev. 1.00 7 ?an?a?? ??? ? 011 pin name function opt i/t o/t descriptions pc?/an? pc? pcpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an? ancsr0 an a/d channel ? pc7/an7 pc7 pcpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p. an7 ancsr0 an a/d channel 7 pd0/tc? pd0 pdpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . tc? st exte? nal time? ? clock inp?t pd1/pwm3 pd1 pdpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . pwm3 ctrl? cmos pwm o?tp?t pd? pd? pdpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . pd3/pclk pd3 pdpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . pclk cmos pe?iphe?al clock o?tp?t pd4/ scs pd4 pdpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . scs st cmos spi slave select pd5/sck/scl pd5 pdpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . sck st cmos spi se?ial clock scl st nmos i ? c clock pd?/sdi/sda pd? pdpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . sdi st spi data inp?t sda st nmos i ? c data pd7/sdo pd7 pdpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . sdo cmos spi data o?tp?t pe0/an8 pe0 pepu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an8 ancsr1 an a/d channel 8 pe1/an9 pe1 pepu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an9 ancsr1 an a/d channel 9 pe?/an10 pe? pepu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an10 ancsr1 an a/d channel 10 pe3/an11 pe3 pepu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an11 ancsr1 an a/d channel 11 pe4/an1? pe4 pepu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an1? ancsr1 an a/d channel 1? pe5/an13 pe5 pepu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an13 ancsr1 an a/d channel 13 pe?/an14 pe? pepu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an14 ancsr1 an a/d channel 14 pe7/an15 pe7 pepu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . an15 ancsr1 an a/d channel 15 pf0/sdoa pf0 pfpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . sdoa cmos spi data o?tp?t pf1/sdia pf1 pfpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . sdia st spi data inp?t pf?~pf7 pfn pfpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . pg0~pg7 pgn pgpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . ph0~ph5 phn phpu st cmos gene?al p??pose i/o. registe? enabled p?ll-?p . vdd vdd pwr powe? s?ppl? vss vss pwr g?o?nd note: i/t: input type; o/t: output type opt: optional by confguration option (co) or register option pwr: power; co: confguration option st: schmitt trigger input; cmos: cmos output; an: analog input or output scom: software controlled lcd com hxt: high frequency crystal oscillator lxt: low frequency crystal oscillator HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ? ?an?a?? ??? ? 011 rev. 1.00 7 ?an?a?? ??? ? 011 absolute maximum ratings supply voltage ................................................................................................ v ss -0.3v to v ss +6.0v input voltage .................................................................................................. v ss -0.3v to v dd +0.3v i ol total .................................................................................................. 100ma total power dissipation ........................................................................................................ 500mw storage temperature .................................................................................................. -50 c to 125c operating temperature ................................................................................................ -40 c to 85 c i oh total ................................................................................................ -100ma note: these are stress ratings only. stresses exceeding the range specifed under absolute maximum ratings may cause substantial damage to the device. functional operation of this device at other conditions beyond those listed in the specifcation is not implied and prolonged exposure to extreme conditions may affect device reliability. d.c. characteristics ta= ?5c symbol parameter test conditions min. typ. max. unit v dd conditions v dd ope? ating voltage f sys =4mhz ?.? 5.5 v f sys =8mhz 3.0 5.5 v f sys =1?mhz 4.5 5.5 v i dd1 ope?ating c???ent (hxt ? hirc? erc) 3v no load? f sys =4mhz 0.8 1.? ma 5v 1.5 ?.?5 ma i dd? ope?ating c???ent (hxt ? hirc? erc) 3v no load? f sys =8mhz 1.4 ?.1 ma 5v ?.8 4.? ma i dd3 ope?ating c???ent (hxt ? hirc? erc) 5v no load? f sys =1?mhz 4 ? ma i dd4 ope?ating c???ent (hirc + lxt ? slow mode) 3v no load? f sys =3?7?8hz (lxt on osc1/osc ?? lvr disabled ? lxtlp=1) 5 10 a 5v 1? ?4 a 3v no load? f sys =3?7?8hz (lxt on xt1/xt ?? lvr disabled ? lxtlp=1) 5 10 a 5v 10 ?0 a i stb1 standb? c???ent (lirc on? lxt off) 3v no load? s? stem halt 5 a 5v 10 a i stb? standb? c???ent (lirc off ? lxt off) 3v no load? s? stem halt 1 a 5v ? a i stb3 standb? c???ent (lirc off ? lxt on? lxtlp=1) 3v no load? s? stem halt (lxt on osc1/osc ?) 5 a 5v 10 a 3v no load? s? stem halt (lxt on xt1/xt ?) 3 a 5v 5 a v il1 inp? t low voltage fo? i/o? tcn and int 0 0.3v dd v v ih1 inp? t high voltage fo? i/o? tcn and int 0.7v dd v dd v v il? inp? t low voltage ( res ) 0 0.4v dd v v ih? inp? t high voltage ( res ) 0.9v dd v dd v v lvr1 low voltage reset 1 v lvr =4.?v 3.98 4.? 4.4? v v lvr ? low voltage reset ? v lvr =3.15v ?.98 3.15 3.3? v v lvr3 low voltage reset 3 v lvr =?.1v 1.98 ?.1 ?.?? v HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 8 ?an?a?? ??? ? 011 rev. 1.00 9 ?an?a?? ??? ? 011 symbol parameter test conditions min. typ. max. unit v dd conditions v lvd1 low voltage detecto ? voltage 1 v lvd = 4.4 v 4.1? 4.4 4.70 v v lvd ? low voltage detecto ? voltage ? v lvd = 3.3 v 3.1? 3.3 3.50 v v lvd ? low voltage detecto ? voltage 3 v lvd = 2.2 v ?.08 ?.? ?.3? v i ol1 i/o po?t sink c???ent (pa ? pb? pc? pd? pe? pf ? pg? ph) 3v v ol =0.1v dd 4 8 ma 5v 10 ?0 ma i oh i/o po?t so??ce c???ent 3v v oh =0.9v dd -? -4 ma 5v -5 -10 ma i ol? pa7 sink c ???ent 5v v ol =0.1v dd ? 3 ma r ph p?ll-high resistance 3v ?0 ?0 100 k 5v 10 30 50 k i scom scom ope?ating c???ent 5v scomc? isel[1:0]=00 17.5 ?5.0 3?.5 a scomc? isel[1:0]=01 35 50 ?5 a scomc? isel[1:0]=10 70 100 130 a scomc? isel[1:0]=11 140 ?00 ??0 a v scom v dd /? voltage fo? lcd com 5v no load 0.475 0.500 0.5?5 v dd note: the standby current (i stb1 ~i stb3 ) and i dd4 are measured with all i/o pins in input mode and tied to v dd . HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 8 ?an?a?? ??? ? 011 rev. 1.00 9 ?an?a?? ??? ? 011 a.c. characteristics ta= ?5c symbol parameter test conditions min. typ. max. unit v dd conditions f sys s?stem clock ?.?v~5.5v 3? 4000 khz 3.0v~5.5v 3? 8000 khz 4.5v~5.5v 3? 1?000 khz f hirc s?stem clock (hirc) 3v/5v ta= ?5 c -?% 4 +?% mhz 3v/5v ta= ?5 c -?% 8 +?% mhz 5v ta= ?5 c -?% 1? +?% mhz 3v/5v ta=0~70 c -5% 4 +5% mhz 3v/5v ta=0~70 c -5% 8 +5% mhz 5v ta=0~70 c -5% 1? +5% mhz ?.?v~3.?v ta=0~70 c -8% 4 +8% mhz 3.0v~5.5v ta=0~70 c -8% 4 +8% mhz 3.0v~5.5v ta=0~70 c -8% 8 +8% mhz 4.5v~5.5v ta=0~70 c -8% 1? +8% mhz ?.?v~3.?v ta=-40 c~85 c -1?% 4 +1?% mhz 3.0v~5.5v ta=-40 c~85 c -1?% 4 +1?% mhz 3.0v~5.5v ta=-40 c~85 c -1?% 8 +1?% mhz 4.5v~5.5v ta=-40 c~85 c -1?% 1? +1?% mhz f erc s?stem clock (erc) 5v ta= ?5 c? r=1?0 k* -?% 4 +?% mhz 5v ta=0~70 c? r=1?0 k* -5% 4 +5% mhz 5v ta=-40 c~85 c? r=1?0 k* -7% 4 +7% mhz ?.?v~5.5v ta=-40 c~85 c? r=1?0 k* -11% 4 +11% mhz f lxt s?stem clock (lxt) 3?7?8 hz t timer time ? inp?t f?eq?enc? (tcn) ?.?v~5.5v 0 4000 khz 3.0v~5.5v 0 8000 khz 4.5v~5.5v 0 1?000 khz f lirc lirc oscillato? 3v 5 10 15 khz 5v ?.5 13 19.5 khz t res exte?nal reset low p?lse width 1 s t sst s?stem sta?t-?p time pe?iod fo? hxt/lxt 1?04 t sys fo? erc/irc (by confguration option) ? t sys 10?4 t sys t int inte???pt f?lse width 1 s t lvr low voltage width to reset 0.?5 1 ? ms restd reset dela ? time 100 ms note: 1. t sys =1/f sys 2.*for f rec , as the resistor tolerance will infuence the frequency a percision resistor is recommended. 3. to maintain the accuracy of the internal hirc oscillator frequency, a 0.1f decoupling capacitor should be connected between vdd and vss and located as close to the device as possible. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 10 ?an?a?? ??? ? 011 rev. 1.00 11 ?an?a?? ??? ? 011 adc characteristics ta= ?5 c symbol parameter test conditions min. typ. max. unit v dd conditions dnl a/c diffe ?ential non-linea?it? 3v t ad =0.5 s -? ? lsb 5v inl adc integ?al non-linea?it? 3v t ad =0.5 s -4 4 lsb 5v i adc additional powe? cons?mption if a/d conve ?te? is used 3v 0.5 0.75 ma 5v 1.0 1.5 ma dac electrical characteristics symbol parameter test conditions min. typ. max. unit v dd conditions v dac dac ope?ating voltage ?.4 v i q dac q ?iescent c???ent 5v code= 0000h v ol =00h ? 3 ma i dac dac ope?ating c???ent 5v 1 khz sin wave? f?ll-scale ( 8k sample ?ate ) 3 4.5 ma res resol?tion 1? bit v o o?tp? t voltage level 0.01 0.99 v dd power-on reset characteristics ta= ?5c symbol parameter test conditions min. typ. max. unit v dd conditions v por v dd sta? t voltage to ens??e powe?-on reset 100 mv rrv dd v dd raising rate to ens??e powe?-on reset 0.035 v/ms t por minim? m time fo? v dd to ?emain at v por to e ns??e powe?-on reset 1 ms HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 10 ?an?a?? ??? ? 011 rev. 1.00 11 ?an?a?? ??? ? 011 system architecture a key factor in the high-performance features of the holtek range of microcontrollers is attributed to the internal system architecture. the range of devices take advantage of the usual features found within risc microcontrollers providing increased speed of operation and enhanced performance. the pipelining scheme is implemented in such a way that instruction fetching and instruction execution are overlapped, hence instructions are effectively executed in one cycle, with the exception of branch or call instructions. an 8-bit wide alu is used in practically all operations of the instruction set. it carries out arithmetic operations, logic operations, rotation, increment, decrement, branch decisions, etc. the internal data path is simplifed by moving data through the accumulator and the alu. certain internal registers are implemented in the data memory and can be directly or indirectly addressed. the simple addressing methods of these registers along with additional architectural features ensure that a minimum of external components is required to provide a functional i/o and a/d control system with maximum reliability and fexibility. clocking and pipelining the main system clock, derived from either a crystal/resonator or rc oscillator is subdivided into four internally generated non-overlapping clocks, t1~t4. the program counter is incremented at the beginning of the t1 clock during which time a new instruction is fetched. the remaining t2~t4 clocks carry out the decoding and execution functions. in this way, one t1~t4 clock cycle forms one instruction cycle. although the fetching and execution of instructions takes place in consecutive instruction cycles, the pipelining structure of the microcontroller ensures that instructions are effectively executed in one instruction cycle. the exception to this are instructions where the contents of the program counter are changed, such as subroutine calls or jumps, in which case the instruction will take one more instruction cycle to execute. for instructions involving branches, such as jump or call instructions, two instruction cycles are required to complete instruction execution. an extra cycle is required as the program takes one cycle to first obtain the actual jump or call address and then another cycle to actually execute the branch. the requirement for this extra cycle should be taken into account by programmers in timing sensitive applications. ? ? ? ? ? system clocking and pipelining HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1? ?an?a?? ??? ? 011 rev. 1.00 13 ?an?a?? ??? ? 011 ? ? ? ? ? ? ? ? ? ? instruction fetching program counter during program execution, the program counter is used to keep track of the address of the next instruction to be executed. it is automatically incremented by one each time an instruction is executed except for instructions, such as "jmp" or "call" that demand a jump to a non- consecutive program memory address. note that the program counter width varies with the program memory capacity depending upon which device is selected. however, it must be noted that only the lower 8 bits, known as the program counter low register, are directly addressable by user. when executing instructions requiring jumps to non-consecutive addresses such as a jump instruction, a subroutine call, interrupt or reset, etc., the microcontroller manages program control by loading the required address into the program counter. for conditional skip instructions, once the condition has been met, the next instruction, which has already been fetched during the present instruction execution, is discarded and a dummy cycle takes its place while the correct instruction is obtained. device program counter program counter high byte pcl register ht4?r0?8b pc13~pc8 pcl7~pcl0 ht4?r0?9b pc14~pc8 14 13 1? 8 7 0 p?og?am co?nte? bp 5 bp ? bank pointe?(bp) the lower byte of the program counter, known as the program counter low register or pcl, is available for program control and is a readable and writeable register. by transferring data directly into this register, a short program jump can be executed directly, however, as only this low byte is available for manipulation, the jumps are limited to the present page of memory, that is 256 locations. when such program jumps are executed it should also be noted that a dummy cycle will be inserted. the lower byte of the program counter is fully accessible under program control. manipulating the pcl might cause program branching, so an extra cycle is needed to pre-fetch. further information on the pcl register can be found in the special function register section. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1? ?an?a?? ??? ? 011 rev. 1.00 13 ?an?a?? ??? ? 011 stack this is a special part of the memory which is used to save the contents of the program counter only. the stack is neither part of the data or program memory space, and is neither readable nor writeable. the activated level is indexed by the stack pointer, sp, and is neither readable nor writeable. at a subroutine call or interrupt acknowledge signal, the contents of the program counter are pushed onto the stack. at the end of a subroutine or an interrupt routine, signaled by a return instruction, ret or reti, the program counter is restored to its previous value from the stack. after a device reset, the stack pointer will point to the top of the stack. device stack levels ht4?r0?8b ht4?r0?9b 8 if the stack is full and an enabled interrupt takes place, the interrupt request fag will be recorded but the acknowledge signal will be inhibited. when the stack pointer is decremented, by ret or reti, the interrupt will be serviced. this feature prevents stack overfow allowing the programmer to use the structure more easily. however, when the stack is full, a call subroutine instruction can still be executed which will result in a stack overfow. precautions should be taken to avoid such cases which might cause unpredictable program branching. arithmetic and logic unit C alu the arithmetic-logic unit or alu is a critical area of the microcontroller that carries out arithmetic and logic operations of the instruction set. connected to the main microcontroller data bus, the alu receives related instruction codes and performs the required arithmetic or logical operations after which the result will be placed in the specifed register. as these alu calculation or operations may result in carry, borrow or other status changes, the status register will be correspondingly updated to refect these changes. the alu supports the following functions: arithmetic operations: add, addm, adc, adcm, sub, subm, sbc, sbcm, daa logic operations: and, or, xor, andm, orm, xorm, cpl, cpla rotation rra, rr, rrca, rrc, rla, rl, rlca, rlc increment and decrement inca, inc, deca, dec branch decision, jmp, sz, sza, snz, siz, sdz, siza, sdza, call, ret, reti HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 14 ?an?a?? ??? ? 011 rev. 1.00 15 ?an?a?? ??? ? 011 program memory the program memory is the location where the user code or program is stored. the device is supplied with one-time programmable, otp, memory where users can program their application code into the device. by using the appropriate programming tools, otp devices offer users the fexibility to freely develop their applications which may be useful during debug or for products requiring frequent upgrades or program changes. structure the program memory has a capacity of 16kx16/32kx16. the program memory is addressed by the program counter and also contains data, table information and interrupt entries. table data, which can be setup in any location within the program memory, is addressed by separate table pointer registers. device capacity banks ht4?r0?8b 1?kx1? 0?1 ht4?r0?9b 3?kx1? 0~3 the devices have their program memory divided into a number of banks which are selected using the bank pointer register. the HT46R068B has its program memory divided into two banks, bank 0 and bank 1. the required bank is selected using bit 5 of the bp register. the ht46r069b has its program memory divided into four banks, from bank0 to bank3. the required bank is selected using bit 5 and bit 6 of the bp register. ? ? ?? ? ? ? ?? ? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 14 ?an?a?? ??? ? 011 rev. 1.00 15 ?an?a?? ??? ? 011 special vectors within the program memory, certain locations are reserved for special usage such as reset and interrupts. reset vector this vector is reserved for use by the device reset for program initialisation. after a device reset is initiated, the program will jump to this location and begin execution. external interrupt vector this vector is used by the external interrupt. if the external interrupt pin on the device receives an edge transition, the program will jump to this location and begin execution if the external interrupt is enabled and the stack is not full. the external interrupt active edge transition type, whether high to low, low to high or both is specifed in the ctrl1 register. timer/event 0/1/2 counter interrupt vector this internal vector is used by the timer/event counters. if a timer/event counter overfow occurs, the program will jump to its respective location and begin execution if the associated timer/event counter interrupt is enabled and the stack is not full. multi-function interrupt vector the multi-function interrupt vector is shared by several internal functions: a time base overfow, an spi/i 2 c or spia data transfer completion. the program will jump to this location and begin execution if the relevant interrupt is enabled and the stack is not full. look-up table any location within the program memory can be defned as a look-up table where programmers can store fxed data. to use the look-up table, the table pointer must frst be setup by placing the lower order address of the look up data to be retrieved in the table pointer register, tblp. this register defnes the lower 8-bit address of the look-up table. after setting up the table pointer, the table data can be retrieved from the current program memory page or last program memory page using the "tabrdc[m]" or "tabrdl[m]" instructions, respectively. when these instructions are executed, the lower order table byte from the program memory will be transferred to the user defined data memory register [m] as specified in the instruction. the higher order table data byte from the program memory will be transferred to the tblh special register. any unused bits in this transferred higher order byte will be read as "0". the following diagram illustrates the addressing/data fow of the look-up table: ? ? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1? ?an?a?? ??? ? 011 rev. 1.00 17 ?an?a?? ??? ? 011 table program example the accompanying example shows how the table pointer and table data is defned and retrieved from the device. this example uses raw table data located in the last page which is stored there using the org statement. the value at this org statement is "7f00h" which refers to the start address of the last page within the 32k program memory of the microcontrollers. the table pointer is setup here to have an initial value of "06h". this will ensure that the frst data read from the data table will be at the program memory address "7f06h" or 6 locations after the start of the last page. note that the value for the table pointer is referenced to the frst address of the present page if the "tabrdc [m]" instruction is being used. the high byte of the table data which in this case is equal to zero will be transferred to the tblh register automatically when the "tabrdl [m]" instruction is executed. because the tblh register is a read-only register and cannot be restored, care should be taken to ensure its protection if both the main routine and interrupt service routine use the table read instructions. if using the table read instructions, the interrupt service routines may change the value of tblh and subsequently cause errors if used again by the main routine. as a rule it is recommended that simultaneous use of the table read instructions should be avoided. however, in situations where simultaneous use cannot be avoided, the interrupts should be disabled prior to the execution of any main routine table-read instructions. note tha t all table related instructions require two instruction cycles to complete their operation. instruction(s) table location b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 tabrdc [m] pc14 pc13 pc1? pc11 pc10 pc9 pc8 @7 @? @5 @4 @3 @? @1 @0 tabrdl [m] 1 1 1 1 1 1 1 @7 @? @5 @4 @3 @? @1 @0 note: pc14~pc8: current program counter bits @7~@0: table pointer tblp bits for the HT46R068B, the table address location is 14 bits, i.e. from b13~b0 for the ht46r069b, the table address location is 15 bits, i.e. from b14~b0 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1? ?an?a?? ??? ? 011 rev. 1.00 17 ?an?a?? ??? ? 011 table read program example: tempreg1 db ? ; temporary register #1 tempreg2 db ? ; temporary register #2 : : mov a, 060h mov bp, a ; select the last bank of prog. memory mov a, 06h ; initialise table pointer - note that this address ; is referenced mov tblp,a ; to the last page or present page : : tabrdl tempreg1 ; transfers value in table referenced by table pointer ; to tempregl ; data at prog. memory address "7f06" transferred to ; tempreg1 and tblh dec tblp ; reduce value of table pointer by one tabrdl tempreg2 ; transfers value in table referenced by table pointer ; to tempreg2 ; data at prog.memory address "7f06" transferred to ; tempreg2 and tblh ; in this example the data "1ah" is transferred to ; tempreg1 and data "0fh" to register tempreg2 ; the value "00h" will be transferred to the high byt ; register tblh : : org 7f00h ; sets initial address of last page dc 00ah, 00bh, 00ch, 00dh, 00eh, 00fh, 01ah, 01bh : : HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 18 ?an?a?? ??? ? 011 rev. 1.00 19 ?an?a?? ??? ? 011 data memory the data memory is a volatile area of 8-bit wide ram internal memory and is the location where temporary information is stored. structure divided into two sections, the frst of these is an area of ram where special function registers are located. these registers have fxed locations and are necessary for correct operation of the device. many of these registers can be read from and written to directly under program control, however, some remain protected from user manipulation. the second area of data memory is reserved for general purpose use. all locations within this area are read and write accessible under program control. device capacity banks ht4?r0?8b 51?x8 0~3 ht4?r0?9b 10?4x8 0~7 the two sections of data memory, the special purpose and general purpose data memory are located at consecutive locations. all are implemented in ram and are 8 bits wide but the length of each memory section is dictated by the type of microcontroller chosen. the start address of the data memory for all devices is the address "00h". all microcontroller programs require an area of read/write memory where temporary data can be stored and retrieved for use later. it is this area of ram memory that is known as general purpose data memory. this area of data memory is fully accessible by the user program for both read and write operations. by using the "set [m].i" and "clr [m].i" instructions individual bits can be set or reset under program control giving the user a large range of fexibility for bit manipulation in the data memory. for some devices, the data memory is subdivided into several banks, which are selected using a bank pointer. only data in bank 0 can be directly addressed, data in bank 1~bank 7 must be indirectly addressed. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 18 ?an?a?? ??? ? 011 rev. 1.00 19 ?an?a?? ??? ? 011 HT46R068B ht46r069b data memory structure note: most of the data memory bits can be directly manipulated using the "set [m].i" and "clr [m]. i" with the exception of a few dedicated bits. the data meomory can also be accessed through the memory pointer registers. special purpose data memory this area of data memory is where registers, necessary for the correct operation of the microcontroller, are stored. most of the registers are both readable and writeable but some are protected and are readable only, the details of which are located under the relevant special function register section. note that for locations that are unused, any read instruction to these addresses will return the value "00h". HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?0 ?an?a?? ??? ? 011 rev. 1.00 ?1 ?an?a?? ??? ? 011 special function registers to ensure successful operation of the microcontroller, certain internal registers are implemented in the data memory area. these registers ensure correct operation of internal functions such as timers, interrupts, etc., as well as external functions such as i/o data control. the location of these registers within the data memory begins at the address "00h" and are mapped from bank 0 to bank 7. any unused data memory locations between these special function registers and the point where the general purpose memory begins is reserved and attempting to read data from these locations will return a value of "00h". indirect addressing registers C iar0, iar1 the indirect addressing registers, iar0 and iar1, although having their locations in normal ram register space, do not actually physically exist as normal registers. the method of indirect addressing for ram data manipulation uses these indirect addressing registers and memory pointers, in contrast to direct memory addressing, where the actual memory address is specifed. actions on the iar0 and iar1 registers will result in no actual read or write operation to these registers but rather to the memory location specifed by their corresponding memory pointer, mp0 or mp1. acting as a pair, iar0 with mp0 and iar1 with mp1 can together access data from the data memory. as the indirect addressing registers are not physically implemented, reading the indirect addressing registers indirectly will return a result of "00h" and writing to the registers indirectly will result in no operation. memory pointers C mp0, mp1 two memory pointers, known as mp0 and mp1 are provided. these memory pointers are physically implemented in the data memory and can be manipulated in the same way as normal registers providing a convenient way with which to indirectly address and track data. mp0 can only be used to indirectly address data in bank 0 while mp1 can be used to address data from bank 0 and bank 7. when any operation to the relevant indirect addressing registers is carried out, the actual address that the microcontroller is directed to, is the address specifed by the related memory pointer. note that indirect addressing using mp1 and iar1 must be used to access any data in bank 1~bank 7 . the following example shows how to clear a section of four data memory locations already defned as locations adres1 to adres4. HT46R068B ht46r069b 00h iar0 iar0 01h mp0 mp0 0?h iar1 iar1 03h mp1 mp1 04h bp bp 05h acc acc 0?h pcl pcl 07h tblp tblp 08h tblh tblh 09h wdts wdts 0ah status status 0bh intc0 intc0 0ch tmr0 tmr0 0dh tmr0c tmr0c 0eh tmr1 tmr1 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?0 ?an?a?? ??? ? 011 rev. 1.00 ?1 ?an?a?? ??? ? 011 0fh tmr1c tmr1c 10h pa pa 11h pac pac 1?h papu papu 13h pawk pawk 14h pb pb 15h pbc pbc 1?h pbpu pbpu 17h pc pc 18h pcc pcc 19h pcpu pcpu 1ah ctrl0 ctrl0 1bh ctrl1 ctrl1 1ch scomc scomc 1dh pwm1 pwm1 1eh intc1 intc1 1fh pwm0 pwm0 ?0h adrl adrl ?1h adrh adrh ??h adcr adcr ?3h acsr acsr ?4h mfic mfic ?5h pd pd ??h pdc pdc ?7h pdpu pdpu ?8h pe pe ?9h pec pec ?ah pepu pepu ?bh pf pf ?ch pfc pfc ?dh pfpu pfpu ?eh ?fh 30h pwm? pwm? 31h ctrl? ctrl? 3?h 3ah 3bh pg pg 3ch pgc pgc 3dh pgpu pgpu 3eh ph 3fh phc 40h phpu 41h tmr?l tmr?l 4?h tmr?h tmr?h 43h tmr?c tmr?c HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?? ?an?a?? ??? ? 011 rev. 1.00 ?3 ?an?a?? ??? ? 011 44h pwm3 pwm3 45h 4?h simc0 simc0 47h simc1 simc1 48h simd simd 49h sima/simc? sima/simc? 4ah sbcr sbcr 4bh sbdr sbdr 4ch 4dh ancsr0 ancsr0 4eh ancsr1 ancsr1 4fh 50h dal dal 51h dah dah 5?h vol vol 53h 54h lvdc lvdc .. 7fh gene?nal p??pose data memo?? 514 b?tes 4 banks (80h~ffh) 10?4 b?tes 8 banks (80h~ffh) indirect addressing program example data .section 'data' adres1 db ? adres2 db ? adres3 db ? adres4 db ? block db ? code .section at 0 code org 00h start: mov a,04h ; setup size of block mov block,a mov a,offset adres1 ; accumulator loaded with frst ram address mov mp0,a ; setup memory pointer with frst ram address loop: clr iar0 ; clear the data at address defned by mp0 inc mp0 ; increment memory pointer sdz block ; check if last memory location has been cleared jmp loop continue: the important point to note here is that in the example shown above, no reference is made to specifc data memory addresses. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?? ?an?a?? ??? ? 011 rev. 1.00 ?3 ?an?a?? ??? ? 011 accumulator C acc the accumulator is central to the operation of any microcontroller and is closely related with operations carried out by the alu. the accumulator is the place where all intermediate results from the alu are stored. without the accumulator it would be necessary to write the result of each calculation or logical operation such as addition, subtraction, shift, etc., to the data memory resulting in higher programming and timing overheads. data transfer operations usually involve the temporary storage function of the accumulator; for example, when transferring data between one user defned register and another, it is necessary to do this by passing the data through the accumulator as no direct transfer between two registers is permitted. program counter low register C pcl to provide additional program control functions, the low byte of the program counter is made accessible to programmers by locating it within the special purpose area of the data memory. by manipulating this register, direct jumps to other program locations are easily implemented. loading a value directly into this pcl register will cause a jump to the specifed program memory location, however, as the register is only 8-bit wide, only jumps within the current program memory page are permitted. when such operations are used, note that a dummy cycle will be inserted. bank pointer C bp in the HT46R068B and ht46r069b devices, the data memory is divided into several banks, from bank 0 to bank 7. a bank pointer is used to select the required data memory bank. only data in bank 0 can be directly addressed as data in bank 1~bank 7 must be indirectly addressed using memory pointer mp1 and indirect addressing register iar1. using memory pointer mp0 and indirect addressing register iar0 will always access data from bank 0, irrespective of the value of the bank pointer. memory pointer mp1 and indirect addressing register iar1 can indirectly address data in either bank 0 or bank 1~bank 7 depending upon the value of the bank pointer. the data memory is initialised to bank 0 after a reset, except for the wdt time-out reset in the idle/ sleep mode, in which case, the data memory bank remains unaffected. it should be noted that special function data memory is not affected by the bank selection, which means that the special function registers can be accessed from within either bank 0 or bank 1~bank 7. directly addressing the data memory will always result in bank 0 being accessed irrespective of the value of the bank pointer. HT46R068B bit 7 6 5 4 3 2 1 0 name pmbp0 dmbp1 dmbp0 r/w r/w r/w r/w por 0 0 0 bit 7~6 unimplemented, read as "0" bit 5 pmbp0 : program memory bank p oint er 0: bank 0 1: bank 1 bit 4~2 unimplemented, read as "0" bit 1,0 dmbp1, dmbp0 : data memory b ank p oint er 00:bank 0 01:bank 1 10:bank 2 11:bank 3 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?4 ?an?a?? ??? ? 011 rev. 1.00 ?5 ?an?a?? ??? ? 011 ht46r069b bit 7 6 5 4 3 2 1 0 bp pmbp1 pmbp0 dmbp? dmbp1 dmbp0 r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 bit 7 unimplemented, read as "0" bit 6, 5 pmbp1, pmbp0 : program memory bank pointer 00: bank 0 01: bank 1 10: bank 2 11: bank 3 bit 4~3 unimplemented, read as "0" bit 2~0 dmbp2, dmbp1, dmbp0 : data memory bank pointer 000: bank 0 001: bank 1 010: bank 2 011: bank 3 100: bank 4 101: bank 5 110: bank 6 111: bank 7 status register C status this 8-bit register contains the zero fag (z), carry fag (c), auxiliary carry fag (ac), overfow flag (ov), power down flag (pdf), and watchdog time-out flag (to). these arithmetic/logical operation and system management flags are used to record the status and operation of the microcontroller. with the exception of the to and pdf fags, bits in the status register can be altered by instructions like most other registers. any data written into the status register will not change the to or pdf flag. in addition, operations related to the status register may give different results due to the different instruction operations. the to fag can be affected only by a system power-up, a wdt time-out or by executing the "clr wdt" or "halt" instruction. the pdf fag is affected only by executing the "halt" or "clr wdt" instruction or during a system power-up. the z, ov, ac and c fags generally refect the status of the latest operations. in addition, on entering an interrupt sequence or executing a subroutine call, the status register will not be pushed onto the stack automatically. if the contents of the status registers are important and if the interrupt routine can change the status register, precautions must be taken to correctly save it. note that bits 0~3 of the status register are both readable and writeable bits. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?4 ?an?a?? ??? ? 011 rev. 1.00 ?5 ?an?a?? ??? ? 011 input/output ports and control registers within the area of special function registers, the port pa, pb, etc data i/o registers and their associated control register pac, pbc, etc play a prominent role. these registers are mapped to specific addresses within the data memory as shown in the data memory table. the data i/o registers, are used to transfer the appropriate output or input data on the port. the control registers specifes which pins of the port are set as inputs and which are set as outputs. to setup a pin as an input, the corresponding bit of the control register must be set high, for an output it must be set low. during program initialisation, it is important to frst setup the control registers to specify which pins are outputs and which are inputs before reading data from or writing data to the i/ o ports. one fexible feature of these registers is the ability to directly program single bits using the "set [m].i" and "clr [m].i" instructions. the ability to change i/o pins from output to input and vice versa by manipulating specifc bits of the i/o control registers during normal program operation is a useful feature of these devices. status register bit 7 6 5 4 3 2 1 0 name to pdf ov z ac c r/w r r r/w r/w r/w r/w por 0 0 x x x x "x" ?nknown bit 7,6 unimplemented, read as "0" bit 5 to : watchdog time-out fag 0: after power up or executing the "clr wdt" or "halt" instruction 1: a watchdog time-out occured. bit 4 pdf : power down fag 0: after power up or executing the "clr wdt" instruction 1: by executing the "halt" instruction bit 3 ov : overfow fag 0: no overfow 1: an operation results in a carry into the highest-order bit but not a carry out of thehighest-order bit or vice versa. bit 2 z : zero fag 0: the result of an arithmetic or logical operation is not zero 1: the result of an arithmetic or logical operation is not zero bit 1 ac : auxiliary fag 0: no auxiliary carry 1: an operation results in a carry out of the low nibbles in addition, or no borrow from the high nibble into the low nibble in subtraction bit 0 c : carry fag 0: no carry-out 1: an operation results in a carry during an addition operation or if a borrow does not take place during a subtraction operation c is also affected by a rotate through carry instruction. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?? ?an?a?? ??? ? 011 rev. 1.00 ?7 ?an?a?? ??? ? 011 system control registers C ctrl0, ctrl1, ctrl2 these registers are used to provide control over various internal functions. some of these include the pfd control, pwm control, certain system clock options, the lxt oscillator low power control, external interrupt edge trigger type, watchdog timer enable function, time base function division ratio, and the lxt oscillator enable control. ctrl0 register bit 7 6 5 4 3 2 1 0 name pcfg pfdcs pwmsel pwmc1 pwmc0 pfdc lxtlp clkmod r/w r/w r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 0 bit 7 pcfg : i/o confguration 0: (pwm0/tc1)/int/pfd pin-shared with pa4/pa3/pa1 1: (pwm0/tc1)/int/pfd pin-shared with pb5/pb4/pb3 bit 6 pfdcs : pfd clock source 0: timer0 1: timer1 bit 5 pwmsel : pwm type selection 0: 6+2 1: 7+1 bit 4 pwmc1 : i/o or pwm1 0: i/o 1: pwm1 bit 3 pwmc0 : i/o or pwm0 0: i/o 1: pwm0 bit 2 pfdc : i/o or pfd 0: i/o 1: pfd bit 1 lxtlp : lxt oscillator low power control function 0: lxt oscillator quick start-up mode 1: lxt oscillator low power mode bit 0 clkmod : system clock mode selection. 0: high speed system clock 1: lxt system clock, high speed oscillator stopped note: if pwm0/1/2/3 output is selected by pwmc0/1/2/3 bit, f tp comes always from f sys . (f tp is the clock source for timer0, time base and pwm) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?? ?an?a?? ??? ? 011 rev. 1.00 ?7 ?an?a?? ??? ? 011 ctrl1 register bit 7 6 5 4 3 2 1 0 name integ1 integ0 tbsel1 tbsel0 wdten3 wdten? wdten1 wdten0 r/w r/w r/w r/w r/w r/w r/w r/w r/w por 1 0 0 0 1 0 1 0 b it 7, 6 integ1, integ0 : external interrupt edge type 00: disable 01: rising edge trigger 10: falling edge trigger 11: dual edge trigger bit 5, 4 tbsel1, tbsel0 : time base period selection 00: 2 10 x (1/f tp ) 01: 2 11 x (1/f tp ) 10: 2 12 x (1/f tp ) 11: 2 13 x (1/f tp ) bit 3~0 wdten3, wdten2, wdten1, wdten0 : wdt function enable 1010: wdt disabled other values: wdt enabled - recommended value is 0101 if the "watchdog timer enable" is configuration option is selected, then the watchdog timer will always be enabled and the wdten3~wdten0 control bits will have no effect. note: the wdt is only disabled when both the wdt configuration option is disabled and when bits wdten3~wdten0=1010. the wdt is enabled when either the wdt configuration option is enabled or when bits wdten3~wdten01010. ctrl2 register bit 7 6 5 4 3 2 1 0 name dacen pwmc3 pwmc? lxten r/w r/w r/w r/w r/w por 0 0 0 1 bit 7 da cen : dac disable/enable control 0: disable 1: enable bit 6 unimplemented, read as "0" bit 5 pwmc3 : io or pwm3 control 0: i/o 1: pwm3 output bit4 pwmc2 : io or pwm2 control 0: i/o 1: pwm2 output bit 3~1 unimplemented, read as "0" bit 0 lxten : lxt oscillator on/off control after execution of halt instruction 0: lxt off in idle mode 1: lxt on in idle mode HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?8 ?an?a?? ??? ? 011 rev. 1.00 ?9 ?an?a?? ??? ? 011 wake-up function register C pawk when the microcontroller enters the idle/sleep mode, various methods exist to wake the device up and continue with normal operation. one method is to allow a falling edge on the i/o pins to have a wake-up function. this register is used to select which port a i/o pins are used to have this wake-up function. pull-high registers C papu, pbpu, pcpu, pdpu, pepu, pfpu the i/o pins, if confgured as inputs, can have internal pull-high resistors connected, which eliminates the need for external pull-high resistors. this register selects which i/o pins are connected to internal pull-high resistors. software com register C scomc the pins pb0~pb3 on port b can be used as scom lines to drive an external lcd panel. to implement this function, the scomc register is used to setup the correct bias voltages on these pins. oscillator various oscillator options offer the user a wide range of functions according to their various application requirements. the flexible features of the oscillator functions ensure that the best optimisation can be achieved in terms of speed and power saving. oscillator selections and operation are selected through a combination of confguration options and registers. system oscillator overview in addition to being the source of the main system clock the oscillators also provide clock sources for other functions such as the watchdog timer, timer/event counter, time base etc. the system oscillator can be provided from a choice of three high speed oscillators, the hxt, erc or hirc oscillators, or a single low speed, lxt crystal oscillator. the lirc oscillator is used only as a watchdog timer clock source. type name freq. pins function exte?nal c??stal hxt 400khz~1?mhz osc1/ osc? high speed s?stem clock exte?nal rc erc 400khz~1?mhz osc1 high speed s?stem clock inte?nal highb speed rc hirc 4? 8 o? 1?mhz high speed s?stem clock exte?nal low speed c??stal lxt 3?7?8hz xt1/ xt? low speed s?stem clock clock so??ce fo? : watchdog? time base? time?/event co?nte?s 0/1 clock/spi/spia inte?nal low speed rc lirc 13khz watchdog time ? clock external crystal/resonator oscillator C hxt the simple connection of a crystal across osc1 and osc2 will create the necessary phase shift and feedback for oscillation. however, for some crystals and most resonator types, to ensure oscillation and accurate frequency generation, it is necessary to add two small value external capacitors, c1 and c2. the exact values of c1 and c2 should be selected in consultation with the crystal or resonator manufacturer's specifcation. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?8 ?an?a?? ??? ? 011 rev. 1.00 ?9 ?an?a?? ??? ? 011 ? ? ? ? crystal/resonator oscillator hxt crystal oscillator c1 and c2 values crystal frequency c1 c2 1?mhz 8pf 10pf 8mhz 8pf 10pf 4mhz 8pf 10pf 1mhz 100pf 100pf note: c1 and c? val?es a?e fo? g?idance onl? . crystal recommended capacitor values external rc oscillator C erc using the erc oscillator only requires that a resistor, with a value between 24k and 1.5m, is connected between osc1 and v dd , and a capacitor is connected between osc and ground, providing a low cost oscillator confguration. it is only the external resistor that determines the oscillation frequency; the external capacitor has no infuence over the frequency and is connected for stability purposes only. device trimming during the manufacturing process and the inclusion of internal frequency compensation circuits are used to ensure that the infuence of the power supply voltage, temperature and process variations on the oscillation frequency are minimised. as a resistance/frequency reference point, it can be noted that with an external 120k resistor connected and with a 5v voltage power supply and temperature of 25 degrees, the oscillator will have a frequency of 4mhz within a tolerance of 2%. here only the osc1 pin is used, which is shared with i/o pin pa6, leaving pin pa5 free for use as a normal i/o pin. external rc oscillator erc HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 30 ?an?a?? ??? ? 011 rev. 1.00 31 ?an?a?? ??? ? 011 internal rc oscillator C hirc the internal rc oscillator is a fully integrated system oscillator requiring no external components. the internal rc oscillator has three fxed frequencies of either 4mhz, 8mhz or 12mhz. device trimming during the manufacturing process and the inclusion of internal frequency compensation circuits are used to ensure that the infuence of the power supply voltage, temperature and process variations on the oscillation frequency are minimised. as a result, at a power supply of either 3v or 5v and at a temperature of 25 degrees, the fxed oscillation frequency of 4mhz, 8mhz or 12mhz will have a tolerance within 2%. note that if this internal system clock option is selected, as it requires no external pins for its operation, i/o pins pa5 and pa6 are free for use as normal i/o pins. internal rc oscillator hirc external 32768hz crystal oscillator C lxt the lxt oscillator is used both as the slow system clock and also as a selectable source clock for some peripheral functions including the watchdog timer, time base, timer/event counters and spi functions. it must be frst enabled using a confguration option. to select the lxt oscillator to be the low speed system oscillator, the clkmod bit in the ctrl0 register should be set high. when a halt instruction is executed, the system clock is stopped, but the lxten bit in the ctrl2 register determines if the lxt oscillator continues running when the microcontroller powers down. setting the lxten bit high will enable the lxt to keep running after a halt instruction is executed and enable the lxt oscillator to remain as a possible clock source for the watchdog timer, the time-base and the timer/event counter 0/1. the lxt oscillator is implemented using a 32768hz crystal connected to pins xt1/xt2. however, for some crystals and to ensure oscillation and accurate frequency generation, it is normally necessary to add two small value external capacitors, c1 and c2. the exact values of c1 and c2 should be selected in consultation with the crystal or resonator manufacturer specifcation. the external parallel feedback resistor, rp, may also be required. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 30 ?an?a?? ??? ? 011 rev. 1.00 31 ?an?a?? ??? ? 011 ? ? ???? - external lxt oscillator - hxt lxt oscillator c1 and c2 values crystal frequency c1 c2 3?7?8hz 8pf 10pf note: 1. c1 and c? val?es a?e fo? g?idance onl? . ?. r p =5m~10m is ?ecommended. 32768hz crystal recommended capacitor values lxt oscillator low power function the lxt oscillator can function in one of two modes, the quick start mode and the low power mode. the mode selection is executed using the lxtlp bit in the ctrl0 register. lxtlp bit lxt mode 0 q?ick sta?t 1 low-powe? after power on the lxtlp bit will be automatically cleared to zero ensuring that the lxt oscillator is in the quick start operating mode. in the quick start mode the lxt oscillator will power up and stabilise quickly. however, after the lxt oscillator has fully powered up it can be placed into the low-power mode by setting the lxtlp bit high. the oscillator will continue to run but with reduced current consumption, as the higher current consumption is only required during the lxt oscillator start-up. in power sensitive applications, such as battery applications, where power consumption must be kept to a minimum, it is therefore recommended that the application program sets the lxtlp bit high about 2 seconds after power-on. it should be noted that, no matter what condition the lxtlp bit is set to, the lxt oscillator will always function normally, the only difference is that it will take more time to start up if in the low-power mode. internal low speed oscillator C lirc the lirc is a fully self-contained free running on-chip rc oscillator with a typical frequency of 13khz at 5v requiring no external components. when the device enters the idle/sleep mode, the system clock will stop running but the wdt oscillator continues to free-run and to keep the watchdog active. however, to preserve power in certain applications the lirc can be disabled via a confguration option. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 3? ?an?a?? ??? ? 011 rev. 1.00 33 ?an?a?? ??? ? 011 operating modes by using the lxt low frequency oscillator in combination with a high frequency oscillator, the system can be selected to operate in a number of different modes. these modes are normal, slow, idle and sleep. mode types and selection the higher frequency oscillators provide higher performance but carry with it the disadvantage of higher power requirements, while the opposite is of course true for the lower frequency oscillators. with the capability of dynamically switching between fast and slow oscillators, the device has the fexibility to optimise the performance/power ratio, a feature especially important in power sensitive portable applications. for these devices the lxt oscillator can run together with any of the high speed oscillators, namely the hxt, erc or the hirc. the clkmod bit in the ctrl0 register can be used to switch the system clock from the selected high speed oscillator to the low speed lxt oscillator. when the halt instruction is executed the lxt oscillator can be chosen to run or not using the lxten bit in the ctrl2 register. ? ? ?? ? ?? ? - ?? ? ?? system clock confgurations for all devices, when the system enters the sleep or idle mode, the high frequency system clock will always stop running. the accompanying tables shows the relationship between the clkmod bit, the halt instruction and the high/low frequency oscillators. the clmod bit can change normal or slow mode. operating mode control halt instruction clkmod bit lxten bit high speed system clock xtal/irc/erc low speed system clock lxt operating mode not exec?ted 0 x r?n on no?mal 1 x stop on slow exec?ted x 1 stop on idle x 0 stop off sleep HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 3? ?an?a?? ??? ? 011 rev. 1.00 33 ?an?a?? ??? ? 011 mode switching the devices are switched between one mode and another using a combination of the clkmod bit in the ctrl0 register and the halt instruction. the clkmod bit chooses whether the system runs in either the normal or slow mode by selecting the system clock to be sourced from either a high or low frequency oscillator. the halt instruction forces the system into either the idle or sleep mode, depending upon whether the lxt oscillator is running or not. the halt instruction operates independently of the clkmod bit condition. when a halt instruction is executed and the lxt oscillator is not running, the system enters the sleep mode the following conditions exist: the system oscillator will stop running and the application program will stop at the "halt" instruction. the data memory contents and registers will maintain their present condition. the wdt will be cleared and resume counting if the wdt clock source is selected to come from the lirc oscillator. the wdt will stop if its clock source originates from the system clock. the i/o ports will maintain their present condition. in the status register, the power down fag, pdf, will be set and the watchdog time-out fag, to, will be cleared. standby current considerations as the main reason for entering the idle/sleep mode is to keep the current consumption of the mcu to as low a value as possible, perhaps only in the order of several micro-amps, there are other considerations which must also be taken into account by the circuit designer if the power consumption is to be minimised. special attention must be made to the i/o pins on the device. all high-impedance input pins must be connected to either a fxed high or low level as any foating input pins could create internal oscillations and result in increased current consumption. care must also be taken with the loads, which are connected to i/o pins, which are setup as outputs. these should be placed in a condition in which minimum current is drawn or connected only to external circuits that do not draw current, such as other cmos inputs. if the configuration options have enabled the watchdog timer internal oscillator lirc then this will continue to run when in the idle/sleep mode and will thus consume some power. for power sensitive applications it may be therefore preferable to use the system clock source for the watchdog timer. the lxt, if confgured for use, will also consume a limited amount of power, as it continues to run when the device enters the idle mode. to keep the lxt power consumption to a minimum level the lxtlp bit in the ctrl0 register, which controls the low power function, should be set high. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 34 ?an?a?? ??? ? 011 rev. 1.00 35 ?an?a?? ??? ? 011 wake-up after the system enters the idle/sleep mode, it can be woken up from one of various sources listed as follows: an external reset an external falling edge on pa0 to pa7 a system interrupt a wdt overfow if the system is woken up by an external reset, the device will experience a full system reset, however, if the device is woken up by a wdt overfow, a watchdog timer reset will be initiated. although both of these wake-up methods will initiate a reset operation, the actual source of the wake-up can be determined by examining the to and pdf fags. the pdf fag is cleared by a system power-up or executing the clear watchdog timer instructions and is set when executing the "halt" instruction. the to fag is set if a wdt time-out occurs, and causes a wake-up that only resets the program counter and stack pointer, the other fags remain in their original status. pins pa0 to pa7 can be setup via the pawuk register to permit a negative transition on the pin to wake-up the system. when a pa0 to pa7 pin wake-up occurs, the program will resume execution at the instruction following the "halt" instruction. if the system is woken up by an interrupt, then two possible situations may occur. the first is where the related interrupt is disabled or the interrupt is enabled but the stack is full, in which case the program will resume execution at the instruction following the "halt" instruction. in this situation, the interrupt which woke-up the device will not be immediately serviced, but will rather be serviced later when the related interrupt is fnally enabled or when a stack level becomes free. the other situation is where the related interrupt is enabled and the stack is not full, in which case the regular interrupt response takes place. if an interrupt request fag is set to "1" before entering the idle/sleep mode, then any future interrupt requests will not generate a wake-up function of the related interrupt will be ignored. no matter what the source of the wake-up event is, once a wake-up event occurs, there will be a time delay before normal program execution resumes. consult the table for the related time. wake-up source oscillator type erc, irc crystal exte?nal res t rsdt + t sst1 t rsdt + t sst? pa po ?t t sst1 t sst? inte???pt wdt overfow note: 1. t rstd (reset delay time), t sys (system clock) 2. t rstd is power-on delay, typical time=100ms 3. t sst1 = 2 or 1024 t sys 4. t sst2 = 1024 t sys wake-up delay time HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 34 ?an?a?? ??? ? 011 rev. 1.00 35 ?an?a?? ??? ? 011 watchdog timer the watchdog timer, also known as the wdt, is provided to inhibit program malfunctions caused by the program jumping to unknown locations due to certain uncontrollable external events such as electrical noise. watchdog timer operation it operates by providing a device reset when the watchdog timer counter overfows. note that if the watchdog timer function is not enabled, then any instructions related to the watchdog timer will result in no operation. setting up the various watchdog timer options are controlled via the confguration options and two internal registers wdts and ctrl1. enabling the watchdog timer can be controlled by both a confguration option and the wdten bits in the ctrl1 internal register in the data memory. confguration option ctrl1 register wdt function disable disable off disable enable on enable x on watchdog timer on/off control the watchdog timer will be disabled if bits wdten3~wdten0 in the ctrl1 register are written with the binary value 1010b and wdt confguration option is disable. this will be the condition when the device is powered up. although any other data written to wdten3~wdten0 will ensure that the watchdog timer is enabled, for maximum protection it is recommended that the value 0101b is written to these bits. the watchdog timer clock can emanate from three different sources, selected by confguration option. these are lxt, f sys /4, or lirc. it is important to note that when the system enters the idle/ sleep mode the instruction clock is stopped, therefore if the confguration options have selected f sys /4 as the watchdog timer clock source, the watchdog timer will cease to function. for systems that operate in noisy environments, using the lirc or the lxt as the clock source is therefore the recommended choice. the division ratio of the prescaler is determined by bits 0, 1 and 2 of the wdts register, known as ws0, ws1 and ws2. if the watchdog timer internal clock source is selected and with the ws0, ws1 and ws2 bits of the wdts register all set high, the prescaler division ratio will be 1:128, which will give a maximum time-out period. under normal program operation, a watchdog timer time-out will initialise a device reset and set the status bit to. however, if the system is in the idle/sleep mode, when a watchdog timer time-out occurs, the device will be woken up, the to bit in the status register will be set and only the program counter and stack pointer will be reset. three methods can be adopted to clear the contents of the watchdog timer. the frst is an external hardware reset, which means a low level on the external reset pin, the second is using the clear watchdog timer software instructions and the third is when a halt instruction is executed. there are two methods of using software instructions to clear the watchdog timer, one of which must be chosen by confguration option. the frst option is to use the single "clr wdt" instruction while the second is to use the two commands "clr wdt1" and "clr wdt2". for the frst option, a simple execution of "clr wdt" will clear the watchdog timer while for the second option, both "clr wdt1" and "clr wdt2" must both be executed to successfully clear the watchdog timer. note that for this second option, if "clr wdt1" is used to clear the watchdog timer, successive executions of this instruction will have no effect, only the execution of a "clr wdt2" instruction will clear the watchdog timer. similarly after the "clr wdt2" instruction has been executed, only a successive "clr wdt1" instruction can clear the watchdog timer. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 3? ?an?a?? ??? ? 011 rev. 1.00 37 ?an?a?? ??? ? 011 ? ? ? ? ? ? ? ?? ?? - ? watchdog timer wdts register bit 7 6 5 4 3 2 1 0 name ws? ws1 ws0 r/w r/w r/w r/w por 1 1 1 bit 7~3 unimplemented, read as "0" bit 2~0 ws2, ws1, ws0 : wdt time-out period selection 000: 2 8 t wdtck 001: 2 9 t wdtck 010: 2 10 t wdtck 011: 2 11 t wdtck 100: 2 12 t wdtck 101: 2 13 t wdtck 110: 2 14 t wdtck 111: 2 15 t wdtck reset and initialisation a reset function is a fundamental part of any microco ntroller ensuring that the device can be set to some predetermined condition irrespective of outside parameters. the most important reset condition is after power is frst applied to the microcontroller. in this case, internal circuitry will ensure that the microcontroller, after a short delay, will be in a well defined state and ready to execute the frst program instruction. after this power-on reset, certain important internal registers will be set to defned states before the program commences. one of these registers is the program counter, which will be reset to zero forcing the microcontroller to begin program execution from the lowest program memory address. in addition to the power-on reset, situations may arise where it is necessary to forcefully apply a reset condition when the microcontroller is running. one example of this is where after power has been applied and the microcontroller is already running, the res line is forcefully pulled low. in such a case, known as a normal operation reset, some of the microcontroller registers remain unchanged allowing the microcontroller to proceed with normal operation after the reset line is allowed to return high. another type of reset is when the watchdog timer overfows and resets the microcontroller. all types of reset operations result in different register conditions being setup. another reset exists in the form of a low voltage reset, lvr, where a full reset, similar to the res reset is implemented in situations where the power supply voltage falls below a certain threshold. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 3? ?an?a?? ??? ? 011 rev. 1.00 37 ?an?a?? ??? ? 011 reset functions there are five ways in which a microcontroller reset can occur, through events occurring both internally and externally: power-on reset the most fundamental and unavoidable reset is the one that occurs after power is frst applied to the microcontroller. as well as ensuring that the program memory begins execution from the frst memory address, a power-on reset also ensures that certain other registers are preset to known conditions. all the i/o port and port control registers will power up in a high condition ensuring that all pins will be frst set to inputs. although the microcontroller has an internal rc reset function, if the v dd power supply rise time is not fast enough or does not stabilise quickly at power-on, the internal reset function may be incapable of providing proper reset operation. for this reason it is recommended that an external rc network is connected to the res pin, whose additional time delay will ensure that the res pin remains low for an extended period to allow the power supply to stabilise. during this time delay, normal operation of the microcontroller will be inhibited. after the res line reaches a certain voltage value, the reset delay time t rstd is invoked to provide an extra delay time after which the microcontroller will begin normal operation. the abbreviation sst in the fgures stands for system start-up timer. power-on reset timing chart note: t rstd is power-on delay, typical time=100ms for most applications a resistor connected between v dd and the res pin and a capacitor connected between v ss and the res pin will provide a suitable external reset circuit. any wiring connected to the res pin should be kept as short as possible to minimise any stray noise interference. for applications that operate within an environment where more noise is present the enhanced reset circuit shown is recommended. external res circuit note: "*" it is recommended that this component is added esd protection. "**" it is recommended that this component is added in environments where power line noise is signifcant. more information regarding external reset circuits is located in application note ha0075e on the holtek website. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 38 ?an?a?? ??? ? 011 rev. 1.00 39 ?an?a?? ??? ? 011 res pin reset this type of reset occurs when the microcontroller is already running and the res pin is forcefully pulled low by external hardware such as an external switch. in this case as in the case of other reset, the program counter will reset to zero and program execution initiated from this point. res reset timing chart note: t rstd is power-on delay, typical time=100ms low voltage reset lvr the microcontroller contains a low voltage reset circuit in order to monitor the supply voltage of the device. the lvr function is selected via a confguration option. if the supply voltage of the device drops to within a range of 0.9v~v lvr such as might occur when changing the battery, the lvr will automatically reset the device internally. for a valid lvr signal, a low supply voltage, i.e., a voltage in the range between 0.9v~v lvr must exist for a time greater than that specifed by t lvr in the a.c. characteristics. if the low supply voltage state does not exceed this value, the lvr will ignore the low supply voltage and will not perform a reset function. the actual v lvr value can be selected via confguration options. low voltage reset timing chart note: t rstd is power-on delay, typical time=100ms watchdog time-out reset during normal operation the watchdog time-out reset during normal operation is the same as a hardware res pin reset except that the watchdog time-out fag to will be set to "1". wdt reset during normal operation timing chart note: t rstd is power-on delay, typical time=100ms watchdog time-out reset during idle/sleep mode the watchdog time-out reset during idle/sleep mode is a little different from other kinds of reset. most of the conditions remain unchanged except that the program counter and the stack pointer will be cleared to "0" and the to fag will be set to "1". refer to the a.c. characteristics for t sst details. wdt time-out reset during idle/sleep timing chart note: the t sst can be chosen to be either 1024 or 2 clock cycles via confguration option if the system clock source is provided by erc or hirc. the sst is 1024 for hxt or lxt. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 38 ?an?a?? ??? ? 011 rev. 1.00 39 ?an?a?? ??? ? 011 reset initial conditions the different types of reset described affect the reset fags in different ways. these fags, known as pdf and to are located in the status register and are controlled by various microcontroller operations, such as the idle/sleep function or watchdog timer. the reset fags are shown in the table: to pdf reset conditions 0 0 powe?-on ?eset ? ? res o? lvr ?eset d??ing no?mal o? slow mode ope?ation 1 ? wdt time-o ?t ?eset d??ing no?mal o? slow mode ope?ation 1 1 wdt time-o ?t ?eset d??ing idle o? sleep mode ope?ation note: "u" stands for unchanged the following table indicates the way in which the various components of the microcontroller are affected after a power-on reset occurs. item condition after reset p?og?am co?nte? reset to ze?o inte???pts all inte???pts will be disabled wdt clea? afte? ?eset? wdt begins co?nting time ?/event co?nte? time ? co?nte? will be t?? ned off p?escale? the time ? co?nte? p?escale? will be clea?ed inp?t/o?tp?t po?ts i/o po?ts will be set?p as inp?ts stack pointe? stack pointe? will point to the top of the stack the different kinds of resets all affect the internal registers of the microcontroller in different ways. to ensure reliable continuation of normal program execution after a reset occurs, it is important to know what condition the microcontroller is in after a particular reset occurs. the following table describes how each type of reset affects each of the microcontroller internal registers. register HT46R068B ht46r069b power-on reset res or lvr reset (normal operation) res or lvr reset (idle/sleep) wdt time-out (normal operation) wdt time-out (idle/sleep) pcl 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 mp0 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? mp1 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? bp C C 0 C C C 0 0 C C 0 C C C 0 0 C C 0 C C C 0 0 C C 0 C C C 0 0 C C ? C C C ? ? bp C 0 0 C C 0 0 0 C 0 0 C C 0 0 0 C 0 0 C C 0 0 0 C 0 0 C C 0 0 0 C ? ? C C ? ? ? acc x x x x x x x x ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? tblp x x x x x x x x ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? tblh x x x x x x x x ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? wdts C C C C C 1 1 1 C C C C C 1 1 1 C C C C C 1 1 1 C C C C C 1 1 1 C C C C C ? ? ? status C C 0 0 x x x x C C ? ? ? ? ? ? C C 0 1 ? ? ? ? C C 1 ? ? ? ? ? C C 1 1 ? ? ? ? intc0 C 0 0 0 0 0 0 0 C 0 0 0 0 0 0 0 C 0 0 0 0 0 0 0 C 0 0 0 0 0 0 0 C ? ? ? ? ? ? ? intc1 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C 0 C ? C ? C ? C ? C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C ? ? ? C ? ? ? mfic C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C 0 0 0 C ? ? ? C ? ? ? tmr0 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? tmr0c 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 ? ? ? ? ? ? ? ? tmr1 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? tmr1c 0 0 0 0 1 C C C 0 0 0 0 1 C C C 0 0 0 0 1 C C C 0 0 0 0 1 C C C ? ? ? ? ? C C C tmr?l x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 40 ?an?a?? ??? ? 011 rev. 1.00 41 ?an?a?? ??? ? 011 register HT46R068B ht46r069b power-on reset res or lvr reset (normal operation) res or lvr reset (idle/sleep) wdt time-out (normal operation) wdt time-out (idle/sleep) tmr?h x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? tmr?c 0 0 0 0 1 C C C 0 0 0 0 1 C C C 0 0 0 0 1 C C C 0 0 0 0 1 C C C ? ? ? ? ? C C C pa 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pac 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pawk 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? papu C 0 0 0 0 0 0 0 C 0 0 0 0 0 0 0 C 0 0 0 0 0 0 0 C 0 0 0 0 0 0 0 C ? ? ? ? ? ? ? pb 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pbc 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pbpu 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? pc 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pcc 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pcpu 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? pd 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pdc 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pdpu 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? pe 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pec 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pepu 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? pf 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pfc 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pfpu 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? pg C C C C C C 1 1 C C C C C C 1 1 C C C C C C 1 1 C C C C C C 1 1 C C C C C C ? ? pgc ? C C C C C C 1 1 C C C C C C 1 1 C C C C C C 1 1 C C C C C C 1 1 C C C C C C ? ? pgpu C C C C C C 0 0 C C C C C C 0 0 C C C C C C 0 0 C C C C C C 0 0 C C C C C C ? ? pg ? 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pgc 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ? ? ? ? ? ? ? ? pgpu 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? ph C C 1 1 1 1 1 1 C C 1 1 1 1 1 1 C C 1 1 1 1 1 1 C C 1 1 1 1 1 1 C C ? ? ? ? ? ? phc C C 1 1 1 1 1 1 C C 1 1 1 1 1 1 C C 1 1 1 1 1 1 C C 1 1 1 1 1 1 C C ? ? ? ? ? ? phpu C C 0 0 0 0 0 0 C C 0 0 0 0 0 0 C C 0 0 0 0 0 0 C C 0 0 0 0 0 0 C C ? ? ? ? ? ? ctrl0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? ctrl1 1 0 0 0 1 0 1 0 1 0 0 0 1 0 1 0 1 0 0 0 1 0 1 0 1 0 0 0 1 0 1 0 ? ? ? ? ? ? ? ? ctrl? 0 C 0 0 C C C 1 0 C 0 0 C C C 1 0 C 0 0 C C C 1 0 C 0 0 C C C 1 ? C ? ? C C C ? scomc 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? pwm0 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? pwm1 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? pwm? x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? pwm3 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? simc0 1 1 1 0 0 0 0 C 1 1 1 0 0 0 0 C 1 1 1 0 0 0 0 C 1 1 1 0 0 0 0 C ? ? ? ? ? ? ? C simc1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 ? ? ? ? ? ? ? ? simd x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? sima/ simc? 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? sbcr 0 1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 1 0 0 0 0 0 ? ? ? ? ? ? ? ? sbdr x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 40 ?an?a?? ??? ? 011 rev. 1.00 41 ?an?a?? ??? ? 011 register HT46R068B ht46r069b power-on reset res or lvr reset (normal operation) res or lvr reset (idle/sleep) wdt time-out (normal operation) wdt time-out (idle/sleep) dal 0 0 0 0 C C C C 0 0 0 0 C C C C 0 0 0 0 C C C C 0 0 0 0 C C C C ? ? ? ? C C C C dah 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? vol 0 0 0 0 C C C C 0 0 0 0 C C C C 0 0 0 0 C C C C 0 0 0 0 C C C C ? ? ? ? C C C C lvdc C C 0 0 C C C C C C 0 0 C C C C C C 0 0 C C C C C C 0 0 C C C C C C ? ? C C C C adrl x x x x C C C C x x x x C C C C x x x x C C C C x x x x C C C C ? ? ? ? C C C C adrh x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ? ? ? ? ? ? ? ? adcr 0 1 C C 0 0 0 0 0 1 C C 0 0 0 0 0 1 C C 0 0 0 0 0 1 C C 0 0 0 0 ? ? C C ? ? ? ? acsr 1 1 C C 0 0 0 0 1 1 C C 0 0 0 0 1 1 C C 0 0 0 0 1 1 C C 0 0 0 0 ? ? C C ? ? ? ? ancsr0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? ancsr1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ? ? ? ? ? ? ? ? input/output ports holtek microcontrollers offer considerable fexibility on their i/o ports. most pins can have either an input or output designation under user program control. additionally, as there are pull-high resistors and wake-up software confgurations, the user is provided with an i/o structure to meet the needs of a wide range of application possibilities. for input operation, these ports are non-latching, which means the inputs must be ready at the t2 rising edge of instruction "mov a,[m]", where m denotes the port address. for output operation, all the data is latched and remains unchanged until the output latch is rewritten. pull-high resistors many product applications require pull-high resistors for their switch inputs usually requiring the use of an external resistor. to eliminate the need for these external resistors, when confgured as an input have the capability of being connected to an internal pull-high resistor. these pull-high resistors are selectable via a register known as papu, pbpu, pcpu, pdpu, pepu and pfpu located in the data memory. the pull-high resistors are implemented using weak pmos transistors. note that pin pa7 does not have a pull-high resistor selection. port a wake-up if the halt instruction is executed, the device will enter the idle/sleep mode, where the system clock will stop resulting in power being conserved, a feature that is important for battery and other low-power applications. various methods exist to wake-up the microcontroller, one of which is to change the logic condition on one of the pa0~pa7 pins from high to low. after a halt instruction forces the microcontroller into entering the idle/sleep mode, the processor will remain idle or in a low-power state until the logic condition of the selected wake-up pin on port a changes from high to low. this function is especially suitable for applications that can be woken up via external switches. note that pins pa0 to pa7 can be selected individually to have this wake-up feature using an internal register known as pawk, located in the data memory. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 4? ?an?a?? ??? ? 011 rev. 1.00 43 ?an?a?? ??? ? 011 pawk, pac, papu, pbc, pbpu, pcc, pcpu, pdc, pdpu, pec, pepu, pfc, pfpu register HT46R068B register name por bit 7 6 5 4 3 2 1 0 pawk 00h pawk7 pawk ? pawk5 pawk4 pawk3 pawk ? pawk1 pawk0 pac ffh pac7 pac ? pac5 pac4 pac3 pac ? pac1 pac0 papu 00h papu ? papu5 papu4 papu3 papu ? papu1 papu0 pbc ffh pbc7 pbc? pbc5 pbc4 pbc3 pbc? pbc1 pbc0 pbpu 00h pbpu7 pbpu? pbpu5 pbpu4 pbpu3 pbpu? pbpu1 pbpu0 pcc ffh pcc7 pcc? pcc5 pcc4 pcc3 pcc? pcc1 pcc0 pcpu 00h pcpu7 pcpu? pcpu5 pcpu4 pcpu3 pcpu? pcpu1 pcpu0 pdc ffh pdc7 pdc? pdc5 pdc4 pdc3 pdc? pdc1 pdc0 pdpu 00h pdpu7 pdpu? pdpu5 pdpu4 pdpu3 pdpu? pdpu1 pdpu0 pec ffh pec7 pec? pec5 pec4 pec3 pec? pec1 pec0 pepu 00h pepu7 pepu? pepu5 pepu4 pepu3 pepu? pepu1 pepu0 pfc ffh pfc7 pfc? pfc5 pfc4 pfc3 pfc? pfc1 pfc0 pfpu 00h pfpu7 pfpu? pfpu5 pfpu4 pfpu3 pfpu? pfpu1 pfpu0 pgc ffh pgc1 pgc0 pgpu 00h pgpu1 pgpu0 "" unimplemented, read as "0" pawkn : pa wake-up function enable 0: disable 1: enable pacn/pbcn/pccn/pdcn/pecn/pfcn/pgcn : i/o type selection 0: output 1: input papun/pbpun/pcpun/pdpun/pepun/pfpun/pgpun : pull-high function enable 0: disable 1: enable HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 4? ?an?a?? ??? ? 011 rev. 1.00 43 ?an?a?? ??? ? 011 ht46r069b register name por bit 7 6 5 4 3 2 1 0 pawk 00h pawk7 pawk ? pawk5 pawk4 pawk3 pawk ? pawk1 pawk0 pac ffh pac7 pac ? pac5 pac4 pac3 pac ? pac1 pac0 papu 00h papu ? papu5 papu4 papu3 papu ? papu1 papu0 pbc ffh pbc7 pbc? pbc5 pbc4 pbc3 pbc? pbc1 pbc0 pbpu 00h pbpu7 pbpu? pbpu5 pbpu4 pbpu3 pbpu? pbpu1 pbpu0 pcc ffh pcc7 pcc? pcc5 pcc4 pcc3 pcc? pcc1 pcc0 pcpu 00h pcpu7 pcpu? pcpu5 pcpu4 pcpu3 pcpu? pcpu1 pcpu0 pdc ffh pdc7 pdc? pdc5 pdc4 pdc3 pdc? pdc1 pdc0 pdpu 00h pdpu7 pdpu? pdpu5 pdpu4 pdpu3 pdpu? pdpu1 pdpu0 pec ffh pec7 pec? pec5 pec4 pec3 pec? pec1 pec0 pepu 00h pepu7 pepu? pepu5 pepu4 pepu3 pepu? pepu1 pepu0 pfc ffh pfc7 pfc? pfc5 pfc4 pfc3 pfc? pfc1 pfc0 pfpu 00h pfpu7 pfpu? pfpu5 pfpu4 pfpu3 pfpu? pfpu1 pfpu0 pgc ffh pgc7 pgc? pgc5 pgc4 pgc3 pgc? pgc1 pgc0 pgpu 00h pgpu7 pgpu? pgpu5 pgpu4 pgpu3 pgpu? pgpu1 pgpu0 phc 3fh phc5 phc4 phc3 phc? phc1 phc0 phpu 00h phpu5 phpu4 phpu3 phpu? phpu1 phpu0 "" unimplemented, read as "0" pawkn : pa wake-up function enable 0: disable 1: enable pacn/pbcn/pccn/pdcn/pecn/pfcn/pgcn/phcn : i/o type selection 0: output 1: input papun/pbpun/pcpun/pdpun/pepun/pfpun/pgpun/phpun : pull-high function enable 0: disable 1: enable i/o port control registers each port has its own control register, known as pac, pbc, pcc, pdc, pec, pfc, pgc, phc which controls the input/output configuration. with this control register, each i/o pin with or without pull-high resistors can be reconfgured dynamically under software control. for the i/o pin to function as an input, the corresponding bit of the control register must be written as a "1". this will then allow the logic state of the input pin to be directly read by instructions. when the corresponding bit of the control register is written as a "0", the i/o pin will be setup as a cmos output. if the pin is currently setup as an output, instructions can still be used to read the output register. however, it should be noted that the program will in fact only read the status of the output data latch and not the actual logic status of the output pin. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 44 ?an?a?? ??? ? 011 rev. 1.00 45 ?an?a?? ??? ? 011 pin-shared functions the fexibility of the microcontroller range is greatly enhanced by the use of pins that have more than one function. limited numbers of pins can force serious design constraints on designers but by supplying pins with multi-functions, many of these diffculties can be overcome. for some pins, the chosen function of the multi-function i/o pins is set by confguration options while for others the function is set by application program control. external interrupt input the external interrupt pin, int, is pin-shared with an i/o pin. to use the pin as an external interrupt input the correct bits in the intc0 register must be programmed. the pin must also be setup as an input by setting the pac3 bit in the port control register. a pull-high resistor can also be selected via the appropriate port pull-high resistor register. note that even if the pin is setup as an external interrupt input the i/o function still remains. external timer/event counter input the timer/event counter pins, tc0, tc1 and tc2 are pin-shared with i/o pins. for these shared pins to be used as timer/event counter inputs, the timer/event counter must be confgured to be in the event counter or pulse width capture mode. this is achieved by setting the appropriate bits in the timer/event counter control register. the pins must also be setup as inputs by setting the appropriate bit in the port control register. pull-high resistor options can also be selected using the port pull-high resistor registers. note that even if the pin is setup as an external timer input the i/o function still remains. pfd output the pfd function output is pin-shared with an i/o pin. the output function of this pin is chosen using the ctrl0 register. note that the corresponding bit of the port control register, must setup the pin as an output to enable the pfd output. if the port control register has setup the pin as an input, then the pin will function as a normal logic input with the usual pull-high selection, even if the pfd function has been selected. pwm outputs the pwm function whose outputs are pin-shared with i/o pins. the pwm output functions are chosen using the ctrl0 and ctrl2 registers. note that the corresponding bit of the port control registers, for the output pin, must setup the pin as an output to enable the pwm output. if the pins are setup as inputs, then the pin will function as a normal logic input with the usual pull- high selections, even if the pwm registers have enabled the pwm function. scom driver pinss pins pb0~pb3 on port b can be used as lcd com driver pins. this function is controlled using the scomc register which will generate the necessary 1/2 bias signals on these four pins. a/d inputs each device in this series has up to 16 inputs to the a/d converter. all of these analog inputs are pin-shared with i/o pins. if these pins are to be used as a/d inputs and not as i/o pins then the corresponding pcrn bits in the ancsr0 and ancsr1 registers, must be properly setup. there are no confguration options associated with the a/d converter. if chosen as i/o pins, then full pull-high resistor confguration options remain, however if used as a/d inputs then any pull-high resistor confguration options associated with these pins will be automatically disconnected. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 44 ?an?a?? ??? ? 011 rev. 1.00 45 ?an?a?? ??? ? 011 pin remapping confguration the pin remapping function enables the function pins pwm0/tc1, int and pfd to be located on different port pins. it is important not to confuse the pin remapping function with the pin-shared function, these two functions have no interdependence. the pcfg bit in the ctrl0 register allows the three function pins pwm0/tc1, int and pfd to be remapped to different port pins. after power up, this bit will be reset to zero, which will defne the default port pins to which these three functions will be mapped. changing this bit will move the functions to other port pins. examination of the pin names on the package diagrams will reveal that some pin function names are repeated, this indicates a function pin that can be remapped to other port pins. if the pin name is bracketed then this indicates its alternative location. pin names without brackets indicates its default location which is the condition after power-on. pcfg bit status pcfg bit 0 1 pin mapping (pwm0/tc1)/pa4 int/pa3 pfd/pa1 [(pwm0/tc1)]/pb5 [int]/pb4 [pfd]/pb3 pin remapping i/o pin structures the diagrams illustrate the i/o pin internal structures. as the exact logical construction of the i/o pin may differ from these drawings, they are supplied as a guide only to assist with the functional understanding of the i/o pins. ??? ?? ? ? ? generic input/output ports HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 4? ?an?a?? ??? ? 011 rev. 1.00 47 ?an?a?? ??? ? 011 ? ? ? ? ? ? pa7 nmos input/output port ? ? ? ?? ? ? ? - ? - - ? - ?? ? ? pb input/output port HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 4? ?an?a?? ??? ? 011 rev. 1.00 47 ?an?a?? ??? ? 011 programming considerations within the user program, one of the frst things to consider is port initialisation. after a reset, the i/o data register and i/o port control register will be set high. this means that all i/o pins will default to an input state, the level of which depends on the other connected circuitry and whether pull-high options have been selected. if the port control registers, are then programmed to setup some pins as outputs, these output pins will have an initial high output value unless the associated port data register is frst programmed. selecting which pins are inputs and which are outputs can be achieved byte-wide by loading the correct value into the port control register or by programming individual bits in the port control register using the "set [m].i" and "clr [m].i" instructions. note that when using these bit control instructions, a read-modify-write operation takes place. the microcontroller must frst read in the data on the entire port, modify it to the required new bit values and then rewrite this data back to the output ports. read modify write timing pins pa0 to pa7 each have a wake-up functions, selected via the pawk register. when the device is in the idle/sleep mode, various methods are available to wake the device up. one of these is a high to low transition of any of the these pins. single or multiple pins on port a can be setup to have this function. timer/event counters the provision of timers form an important part of any microcontroller, giving the designer a means of carrying out time related functions. the devices contain two 8-bit and one 16-bit timer. as the timers have three different operating modes, they can be confgured to operate as a general timer, an external event counter or as a pulse width capture device. the provision of an internal prescaler to the clock circuitry on gives added range to the timers. there are two types of registers related to the timer/event counters. the frst is the register that contains the actual value of the timer and into which an initial value can be preloaded. reading from this register retrieves the contents of the timer/event counter. the second type of associated register is the timer control register which defnes the timer options and determines how the timer is to be used. the device can have the timer clock confgured to come from the internal clock source. in addition, the timer clock source can also be confgured to come from an external timer pin. confguring the timer/event counter input clock source the timer/event counter clock source can originate from various sources, an internal clock or an external pin. the internal clock source is used when the timer is in the timer mode or in the pulse width capture mode. for some timer/event counters, this internal clock source is frst divided by a prescaler, the division ratio of which is conditioned by the timer control register bits. an external clock source is used when the timer is in the event counting mode, the clock source being provided on an external timer pin tcn. depending upon the condition of the tneg bit, each high to low, or low to high transition on the external timer pin will increment the counter by one. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 48 ?an?a?? ??? ? 011 rev. 1.00 49 ?an?a?? ??? ? 011 timer registers C tmr0, tmr1, tmr2l, tmr2h the timer registers are special function registers located in the special purpose data memory and is the place where the actual timer value is stored. these registers are known as tmr0, tmr1, tmr2l and tmr2h. the value in the timer registers increases by one each time an internal clock pulse is received or an external transition occurs on the external timer pin. the timer will count from the initial value loaded by the preload register to the full count of ffh for the 8-bit timer/ event counter or ffffh for the 16-bit timer/event counters, at which point the timer overfows and an internal interrupt signal is generated. the timer value will then be reset with the initial preload register value and continue counting. note that to achieve a maximum full range count of ffh or ffffh, the preload register must frst be cleared to all zeros. it should be noted that after power-on, the preload registers will be in an unknown condition. note that if the timer/ event counter is in an off condition and data is written to its preload register, this data will be immediately written into the actual counter. however, if the counter is enabled and counting, any new data written into the preload data register during this period will remain in the preload register and will only be written into the actual counter the next time an overfow occurs. timer control registers C tmr0c, tmr1c, tmr2c the fexible features of the holtek microcontroller timer/event counters enable them to operate in three different modes, the options of which are determined by the contents of their respective control register. the timer control register is known as tmrnc. it is the timer control register together with its corresponding timer register that control the full operation of the timer/event counter. before the timer can be used, it is essential that the timer control register is fully programmed with the right data to ensure its correct operation, a process that is normally carried out during program initialisation. to choose which of the three modes the timer is to operate in, either in the timer mode, the event counting mode or the pulse width capture mode, bits 7 and 6 of the timer control register, which are known as the bit pair tnm1/tnm0, must be set to the required logic levels. the timer-on bit, which is bit 4 of the timer control register and known as tnon, provides the basic on/off control of the respective timer. setting the bit high allows the counter to run, clearing the bit stops the counter. bits 0~2 of the timer control register determine the division ratio of the input clock prescaler. the prescaler bit settings have no effect if an external clock source is used. if the timer is in the event count or pulse width capture mode, the active transition edge level type is selected by the logic level of bit 3 of the timer control register which is known as tneg. the tns bit selects the internal clock source. ? ? ? ? ? ? ? ? ? ? - ? ? ? ? ?? ? ? ? ? ? ? ? ? ? clock structure for timer/pwm/time base HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 48 ?an?a?? ??? ? 011 rev. 1.00 49 ?an?a?? ??? ? 011 ? ?? ? ? ? ? - ? ? ? 8-bit timer/event counter 0 structure ? ? ? ?? ? - ? ? ? ? 8-bit timer/event counter 1 structure ?? ? ? ? ? - ? ? ? 16-bit timer/event counter 2 structure 0 mux pfd0 pfd1 pfd o?tp?t pfdcs 1 note: if pwm0/pwm1/pwm2/pwm4 is enabled, then f tp comes from f sys (ignore t0s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 50 ?an?a?? ??? ? 011 rev. 1.00 51 ?an?a?? ??? ? 011 tmr0c register bit 7 6 5 4 3 2 1 0 name t0m1 t0m0 t0s t0on t0eg t0psc? t0psc1 t0psc0 r/w r/w r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 1 0 0 0 bit 7,6 t0m1, t0m0 : timer0 operation mode selection 00: no mode available 01: event counter mode 10: timer mode 11: pulse width capture mode bit 5 t0s : timer clock source 0: f sys 1: lxt oscillator t0s selects the clock source for ftp which is provided for timer 0~2, the time- base and the pwm. if the pwm is enabled, then f sys will be selected, overriding the t0s selection. bit 4 t0on : timer/event counter counting enable 0: disable 1: enable bit 3 t0eg : event counter active edge selection 0: count on raising edge 1: count on falling edge pulse width capture active edge selection 0: start counting on falling edge, stop on raising edge 1: start counting on raising edge, stop on falling edge bit 2~0 t0psc2, t0psc1, t0psc0 : timer prescaler rate selection timer internal clock= 000: f tp 001: f tp /2 010:f tp /4 011:f tp /8 100:f tp /16 101:f tp /32 110:f tp /64 111:f tp /128 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 50 ?an?a?? ??? ? 011 rev. 1.00 51 ?an?a?? ??? ? 011 tmr1c register bit 7 6 5 4 3 2 1 0 name t1m1 t1m0 t1s t1on t1eg r/w r/w r/w r/w r/w r/w por 0 0 0 0 1 bit 7,6 t1m1, t1m0 : timer 1 operation mode selection 00: no mode available 01: event counter mode 10: timer mode 11: pulse width capture mode bit 5 t1s : timer clock source 0: f sys /4 1: lxt oscillator bit 4 t1on : timer/event counter counting enable 0: disable 1: enable bit 3 t1eg : event counter active edge selection 0: count on raising edge 1: count on falling edge pulse width capture active edge selection 0: start counting on falling edge, stop on raising edge 1: start counting on raising edge, stop on falling edge bit 2~0 unimplemented, read as "0" tmr2c register bit 7 6 5 4 3 2 1 0 name t?m1 t?m0 t?s t?on t?eg r/w r/w r/w r/w r/w r/w por 0 0 0 0 1 bit 7,6 t2m 1, t2m0 : timer 1 operation mode selection 00: no mode available 01: event counter mode 10: timer mode 11: pulse width capture mode bit 5 t2s : timer clock source 0: f sys /4 1: lxt oscillator bit 4 t2on : timer/event counter counting enable 0: disable 1: enable bit 3 t2eg : event counter active edge selection 0: count on raising edge 1: count on falling edge pulse width capture active edge selection 0: start counting on falling edge, stop on raising edge 1: start counting on raising edge, stop on falling edge bit 2~0 unimplemented, read as "0" HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 5? ?an?a?? ??? ? 011 rev. 1.00 53 ?an?a?? ??? ? 011 to choose which of the three modes the timer is to operate in, either in the timer mode, the event counting mode or the pulse width capture mode, bits 7 and 6 of the timer control register, which are known as the bit pair tnm1/tnm0, must be set to the required logic levels. the timer-on bit, which is bit 4 of the timer control register and known as tnon, provides the basic on/off control of the respective timer. setting the bit high allows the counter to run, clearing the bit stops the counter. bits 0~2 of the timer control register determine the division ratio of the input clock prescaler. the prescaler bit settings have no effect if an external clock source is used. if the timer is in the event count or pulse width capture mode, the active transition edge level type is selected by the logic level of bit 3 of the timer control register which is known as tneg. the tns bit selects the internal clock source if used. timer mode in this mode, the timer/event counter can be utilised to measure fxed time intervals, providing an internal interrupt signal each time the timer/event counter overfows. to operate in this mode, the operating mode select bit pair, tnm1/tnm0, in the timer control register must be set to the correct value as shown. cont?ol registe? ope?ating mode bit7 bit6 select bits fo? the time? mode 1 0 in this mode the internal clock is used as the timer clock. the timer input clock source is either f sys , f sys /4 or the lxt oscillator. however, this timer clock source is further divided by a prescaler, the value of which is determined by the bits tnpsc2~tnpsc0 in the timer control register. the timer-on bit, tnon must be set high to enable the timer to run. each time an internal clock high to low transition occurs, the timer increments by one; when the timer is full and overfows, an interrupt signal is generated and the timer will reload the value already loaded into the preload register and continue counting. a timer overfow condition and corresponding internal interrupt is one of the wake-up sources, however, the internal interrupts can be disabled by ensuring that the etni bits of the intcn register are reset to zero. event counter mode in this mode, a number of externally changing logic events, occurring on the external timer tcn pin, can be recorded by the timer/event counter. to operate in this mode, the operating mode select bit pair, tnm1/tnm0, in the timer control register must be set to the correct value as shown. cont?ol registe? ope?ating mode bit7 bit6 select bits fo? the event co?nte? mode 0 1 in this mode, the external timer tcn pin, is used as the timer/event counter clock source, however it is not divided by the internal prescaler. after the other bits in the timer control register have been setup, the enable bit tnon, which is bit 4 of the timer control register, can be set high to enable the timer/event counter to run. if the active edge select bit, tneg, which is bit 3 of the timer control register, is low, the timer/event counter will increment each time the external timer pin receives a low to high transition. if the tneg is high, the counter will increment each time the external timer pin receives a high to low transition. when it is full and overfows, an interrupt signal is generated and the timer/event counter will reload the value already loaded into the preload register and continue counting. the interrupt can be disabled by ensuring that the timer/event counter interrupt enable bit in the corresponding interrupt control register, is reset to zero. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 5? ?an?a?? ??? ? 011 rev. 1.00 53 ?an?a?? ??? ? 011 as the external timer pin is shared with an i/o pin, to ensure that the pin is confgured to operate as an event counter input pin, two things have to happen. the frst is to ensure that the operating mode select bits in the timer control register place the timer/event counter in the event counting mode, the second is to ensure that the port control register configures the pin as an input. it should be noted that in the event counting mode, even if the is in the idle/sleep mode, the timer/event counter will continue to record externally changing logic events on the timer input tcn pin. as a result when the timer overfows it will generate a timer interrupt and corresponding wake-up source. timer mode timing chart event counter mode timing chart (tneg=1) pulse width capture mode in this mode, the timer/event counter can be utilised to measure the width of external pulses applied to the external timer pin. to operate in this mode, the operating mode select bit pair, tnm1/tnm0, in the timer control register must be set to the correct value as shown. cont?ol registe? ope?ating mode bit7 bit6 select bits fo? the p?lse width capt??e mode 1 1 in this mode the internal clock, f sys , f sys /4 or the lxt, is used as the internal clock for the 8-bit timer/event counter. however, the clock source, f sys , for the 8-bit timer is further divided by a prescaler, the value of which is determined by the prescaler rate select bits tnpsc2~tnpsc0, which are bits 2~0 in the timer control register. after the other bits in the timer control register have been setup, the enable bit tnon, which is bit 4 of the timer control register, can be set high to enable the timer/event counter, however it will not actually start counting until an active edge is received on the external timer pin. if the active edge select bit tneg, which is bit 3 of the timer control register, is low, once a high to low transition has been received on the external timer pin, the timer/event counter will start counting until the external timer pin returns to its original high level. at this point the enable bit will be automatically reset to zero and the timer/event counter will stop counting. if the active edge select bit is high, the timer/event counter will begin counting once a low to high transition has been received on the external timer pin and stop counting when the external timer pin returns to its original low level. as before, the enable bit will be automatically reset to zero and the timer/event counter will stop counting. it is important to note that in the pulse width capture mode, the enable bit is automatically reset to zero when the external control signal on the external timer pin returns to its original level, whereas in the other two modes the enable bit can only be reset to zero under program control. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 54 ?an?a?? ??? ? 011 rev. 1.00 55 ?an?a?? ??? ? 011 the residual value in the timer/event counter, which can now be read by the program, therefore represents the length of the pulse received on the tcn pin. as the enable bit has now been reset, any further transitions on the external timer pin will be ignored. the timer cannot begin further pulse width capture until the enable bit is set high again by the program. in this way, single shot pulse measurements can be easily made. it should be noted that in this mode the timer/event counter is controlled by logical transitions on the external timer pin and not by the logic level. when the timer/event counter is full and overfows, an interrupt signal is generated and the timer/event counter will reload the value already loaded into the preload register and continue counting. the interrupt can be disabled by ensuring that the timer/event counter interrupt enable bit in the corresponding interrupt con trol register, is reset to zero. as the tcn pin is shared with an i/o pin, to ensure that the pin is confgured to operate as a pulse width capture pin, two things have to happen. the frst is to ensure that the operating mode select bits in the timer control register place the timer/event counter in the pulse width capture mode, the second is to ensure that the port control register confgures the pin as an input. prescaler bits t0psc0~t0psc2 of the tmr0c register can be used to defne a division ratio for the internal clock source of the timer/event counter enabling longer time out periods to be setup. pfd function the programmable frequency divider provides a means of producing a variable frequency output suitable for applications, such as piezo-buzzer driving or other interfaces requiring a precise frequency generator. the timer/event counter overflow signal is the clock source for the pfd function, which is controlled by pfdcs bit in ctrl0. for applicable devices the clock source can come from either timer/event counter 0 or timer/event counter 1. the output frequency is controlled by loading the required values into the timer prescaler and timer registers to give the required division ratio. the counter will begin to count-up from this preload register value until full, at which point an overfow signal is generated, causing both the pfd outputs to change state. the counter will then be automatically reloaded with the preload register value and continue counting-up. if the ctrl0 register has selected the pfd function, then for pfd output to operate, it is essential for the port a control register pac, to setup the pfd pins as outputs. pa1 must be set high to activate the pfd. the output data bits can be used as the on/off control bit for the pfd outputs. note that the pfd outputs will all be low if the output data bit is cleared to zero. using this method of frequency generation, and if a crystal oscillator is used for the system clock, very precise values of frequency can be generated. ? ? ? ? ? ? ? ? ? pulse width capture mode timing chart (tne=0) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 54 ?an?a?? ??? ? 011 rev. 1.00 55 ?an?a?? ??? ? 011 pfd function i/o interfacing the timer/event counter, when configured to run in the event counter or pulse width capture mode, requires the use of an external timer pin for its operation. as this pin is a shared pin it must be confgured correctly to ensure that it is setup for use as a timer/event counter input pin. this is achieved by ensuring that the mode select bits in the timer/event counter control register, select either the event counter or pulse width capture mode. additionally the corresponding port control register bit must be set high to ensure that the pin is setup as an input. any pull-high resistor connected to this pin will remain valid even if the pin is used as a timer/event counter input. programming considerations when confgured to run in the timer mode, the internal system clock is used as the timer clock source and is therefore synchronised with the overall operation of the microcontroller. in this mode when the appropriate timer register is full, the microcontroller will generate an internal interrupt signal directing the program fow to the respective internal interrupt vector. for the pulse width capture mode, the internal system clock is also used as the timer clock source but the timer will only run when the correct logic condition appears on the external timer input pin. as this is an external event and not synchronised with the internal timer clock, the microcontroller will only see this external event when the next timer clock pulse arrives. as a result, there may be small differences in measured values requiring programmers to take this into account during programming. the same applies if the timer is confgured to be in the event counting mode, which again is an external event and not synchronised with the internal system or timer clock. when the timer/event counter is read, or if data is written to the preload register, the clock is inhibited to avoid errors, however as this may result in a counting error, this should be taken into account by the programmer. care must be taken to ensure that the timers are properly initialised before using them for the frst time. the associated timer enable bits in the interrupt control register must be properly set otherwise the internal interrupt associated with the timer will remain inactive. the edge select, timer mode and clock source control bits in timer control register must also be correctly set to ensure the timer is properly confgured for the required application. it is also important to ensure that an initial value is frst loaded into the timer registers before the timer is switched on; this is because after power-on the initial values of the timer registers are unknown. after the timer has been initialised the timer can be turned on and off by controlling the enable bit in the timer control register. when the timer/event counter overfows, its corresponding interrupt request fag in the interrupt control register will be set. if the timer/event counter interrupt is enabled this will in turn generate an interrupt signal. however irrespective of whether the interrupts are enabled or not, a timer/ event counter overflow will also generate a wake-up signal if the device is in a power-down condition. this situation may occur if the timer/event counter is in the event counting mode HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 5? ?an?a?? ??? ? 011 rev. 1.00 57 ?an?a?? ??? ? 011 and if the external signal continues to change state. in such a case, the timer/event counter will continue to count these external events and if an overfow occurs the device will be woken up from its power-down condition. to prevent such a wake-up from occurring, the timer interrupt request fag should frst be set high before issuing the "halt" instruction to enter the idle/sleep mode. timer program example the program shows how the timer/event counter registers are setup along with how the interrupts are enabled and managed. note how the timer/event counter is turned on, by setting bit 4 of the timer control register. the timer/event counter can be turned off in a similar way by clearing the same bit. this example program sets the timer/event counters to be in the timer mode, which uses the internal system clock as their clock source. pfd programming example org 04h ; external interrupt vector org 08h ; timer counter 0 interrupt vector jmp tmr0int ; jump here when timer 0 overfows : : org 20h ; main program : : ;internal timer 0 interrupt routine tmr0int: : ; timer 0 main program placed here : : begin: ;setup timer 0 registers mov a,09bh ; setup timer 0 preload value mov tmr0,a mov a,081h ; setup timer 0 control register mov tmr0c,a ; timer mode and prescaler set to /2 ;setup interrupt register mov a,00dh ; enable master interrupt and both timer interrupts mov intc0,a : : set tmr0c.4 ; start timer 0 : : time base the device includes a time base function which is used to generate a regular time interval signal. the time base time interval magnitude is determined using an internal 13 stage counter sets the division ratio of the clock source. this division ratio is controlled by both the tbsel0 and tbsel1 bits in the ctrl1 register. the clock source is selected using the t0s bit in the tmr0c register. when the time base time out, a time base interrupt signal will be generated. it should be noted that as the time base clock source is the same as the timer/event counter clock source, care should be taken when programming. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 5? ?an?a?? ??? ? 011 rev. 1.00 57 ?an?a?? ??? ? 011 pulse width modulator every device includes a multiple output 8-bit pwm function. useful for such applications such as motor speed control, the pwm function provides outputs with a fxed frequency but with a duty cycle that can be varied by setting particular values into the corresponding pwm register . ? ? ? pwm block diagram device channels mode pins registers ht4?r0?8b ht4?r0?9b 4 ?+? 7+1 pa4 pc3 pc? pd1 pwm0 pwm1 pwm? pwm3 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 58 ?an?a?? ??? ? 011 rev. 1.00 59 ?an?a?? ??? ? 011 pwm operation a single register, known as pwmn and located in the data memory is assigned to each pulse width modulator channel. it is here that the 8-bit value, which represents the overall duty cycle of one modulation cycle of the output waveform, should be placed. to increase the pwm modulation frequency, each modulation cycle is subdivided into two or four individual modulation subsections, known as the 7+1 mode or 6+2 mode respectively. the required mode and the on/ off control for each pwm channel is selected using the ctrl0 and ctrl2 registers. note that when using the pwm, it is only necessary to write the required value into the pwmn register and select the required mode setup and on/off control using the ctrl0 and ctrl2 registers, the subdivision of the waveform into its sub-modulation cycles is implemented automatically within the microcontroller hardware. the pwm clock source is the system clock f sys . this method of dividing the original modulation cycle into a further 2 or 4 sub-cycles enable the generation of higher pwm frequencies which allow a wider range of applications to be served. the difference between what is known as the pwm cycle frequency and the pwm modulation frequency should be understood. as the pwm clock is the system clock, f sys , and as the pwm value is 8-bits wide, the overall pwm cycle frequency is f sys /256. however, when in the 7+1 mode of operation the pwm modulation frequency will be f sys /128, while the pwm modulation frequency for the 6+2 mode of operation will be f sys /64. pwm modulation pwm cycle frequency pwm cycle duty f sys /?4 fo? (?+?) bits mode f sys /1?8 fo? (7+1) bits mode f sys /?5? [pwm]/?5? 6+2 pwm mode each full pwm cycle, as it is controlled by an 8-bit pwm register, has 256 clock periods. however, in the 6+2 pwm mode, each pwm cycle is subdivided into four individual sub-cycles known as modulation cycle 0 ~ modulation cycle 3, denoted as i in the table. each one of these four sub-cycles contains 64 clock cycles. in this mode, a modulation frequency increase of four is achieved. the 8-bit pwm register value, which represents the overall duty cycle of the pwm waveform, is divided into two groups. the frst group which consists of bit2~bit7 is denoted here as the dc value. the second group which consists of bit0~bit1 is known as the ac value. in the 6+2 pwm mode, the duty cycle value of each of the four modulation sub-cycles is shown in the following table. parameter ac (0~3) dc (duty cycle) mod?lation c?cle i (i=0~3) i < ac dc+1 ?4 i R ac dc ?4 6+2 mode modulation cycle values the following diagram illustrates the waveforms associated with the 6+2 mode of pwm operation. it is important to note how the single pwm cycle is subdivided into 4 individual modulation cycles, numbered from 0~3 and how the ac value is related to the pwm value. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 58 ?an?a?? ??? ? 011 rev. 1.00 59 ?an?a?? ??? ? 011 ? 6+2 pwm mode pwm register for 6+2 mode 7+1 pwm mode each full pwm cycle, as it is controlled by an 8-bit pwm register, has 256 clock periods. however, in the 7+1 pwm mode, each pwm cycle is subdivided into two individual sub-cycles known as modulation cycle 0 ~ modulation cycle 1, denoted as i in the table. each one of these two sub-cycles contains 128 clock cycles. in this mode, a modulation frequency increase of two is achieved. the 8-bit pwm register value, which represents the overall duty cycle of the pwm waveform, is divided into two groups. the first group which consists of bit1~bit7 is denoted here as the dc value. the second group which consists of bit0 is known as the ac value. in the 7+1 pwm mode, the duty cycle value of each of the two modulation sub-cycles is shown in the following table. parameter ac (0~1) dc (duty cycle) mod?lation c?cle i (i=0~1) i < ac dc+1 1?8 i R ac dc 1?8 7+1 mode modulation cycle values the following diagram illustrates the waveforms associated with the 7+1 mode pwm operation. it is important to note how the single pwm cycle is subdivided into 2 individual modulation cycles, numbered 0 and 1 and how the ac value is related to the pwm value. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?0 ?an?a?? ??? ? 011 rev. 1.00 ?1 ?an?a?? ??? ? 011 pwm output control the pwm outputs are pin-shared with the i/o pins pa4, pc2 and pc3. to operate as a pwm output and not as an i/o pin, the correct bits must be set in the ctrl0 and ctrl2 register. a zero value must also be written to the corresponding bit in the i/o port control register pac.4, pcc.2 and pcc.3 to ensure that the corresponding pwm output pin is setup as an output. after these two initial steps have been carried out, and of course after the required pwm value has been written into the pwmn register, writing a high value to the corresponding bit in the output data register pa.4, pc.2 and pc.3 will enable the pwm data to appear on the pin. writing a zero value will disable the pwm output function and force the output low. in this way, the port data output registers can be used as an on/off control for the pwm function. note that if the ctrl0 and ctrl2 registers have selected the pwm function, but a high value has been written to its corresponding bit in the pac or pcc control register to confgure the pin as an input, then the pin can still function as a normal input line, with pull-high resistor options. ? 7+1 pwm mode pwm register for 7+1 mode pwm programming example the following sample program shows how the pwm0 output is setup and controlled. mov a,64h ; setup pwm value of decimal 100 mov pwm0,a set ctrl0.5 ; select the 7+1 pwm mode set ctrl0.3 ; select pin pa4 to have a pwm function clr pac.4 ; setup pin pa4 as an output set pa.4 ; enable the pwm output : : clr pa.4 ; disable the pwm output_ pin ; pa4 forced low HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?0 ?an?a?? ??? ? 011 rev. 1.00 ?1 ?an?a?? ??? ? 011 analog to digital converter the need to interface to real world analog signals is a common requirement for many electronic systems. however, to properly process these signals by a , they must frst be converted into digital signals by a/d converters. by integrating the a/d conversion electronic circuitry into the , the need for external components is reduced signifcantly with the corresponding follow-on benefts of lower costs and reduced component space requirements. a/d overview the device contains an 4/8-channel analog to digital converter which can directly interface to external analog signals, such as that from sensors or other control signals and convert these signals directly into either a 12-bit digital value. part no. input channels conversion bits input pins ht4?r0?8b 1? 1? pa0~pa3 pc0~pc1 pc?~pc7 pe0~pe7 ht4?r0?9b the accompanying block diagram shows the overall internal structure of the a/d converter, together with its associated registers. a/d converter data registers C adrl, adrh the device, which has an internal 12-bit a/d converter, requires two data registers, a high byte register, known as adrh, and a low byte register, known as adrl. after the conversion process takes place, these registers can be directly read by the microcontroller to obtain the digitised conversion value. only the high byte register, adrh, utilises its full 8-bit contents. the low byte register utilises only 4 bit of its 8-bit contents as it contains only the lowest bits of the 12-bit converted value. in the following table, d0~d11 is the a/d conversion data result bits. register bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 adrl d3 d? d1 d0 adrh d11 d10 d9 d8 d7 d? d5 d4 a/d data registers a/d converter control registers C adcr, acsr, ancsr1, ancsr0 to control the function and operation of the a/d converter, four control registers known as adcr, acsr, ancsr1 and ancsr0 are provided. these 8-bit registers defne functions such as the selection of which analog channel is connected to the internal a/d converter, which pins are used as analog inputs and which are used as normal i/os, the a/d clock source as well as controlling the start function and monitoring the a/d converter end of conversion status. the acs3~acs0 bits in the adcr register defne the channel number. as the device contains only one actual analog to digital converter circuit, each of the individual 8 analog inputs must be routed to the converter. it is the function of the acs3~acs0 bits in the adcr register to determine which analog channel is actually connected to the internal a/d converter. the two control registers, ancsr1,ancsr0, determine which pins on pa0~pa3, pc0, pc1, pc6, pc7, pe0~pe7 are used as analog inputs for the a/d converter and which pins are to be used as normal i/o pins. if the 16-bit address on pcr15~pcr0 has a value of ffh, then all 16 pins, namely an0~an15 will all be set as analog inputs. to reduce the power consumption in HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?? ?an?a?? ??? ? 011 rev. 1.00 ?3 ?an?a?? ??? ? 011 normal run, the adc module can be turned off by setting adonb=1 in acsr. once the adc module is turned off, the adc module and analog channel have no power consumption no matter what voltage level is on analog input. if the i/o lines is selected as an i/o function and the analog input pin voltage is not equal to v dd or v ss , there user may have to take care idd/istb current consumed by the pin-shared logic input function no matter the adc module is on or off. if the adc module is turned off, then all the adc pin-shared i/o pins will be setup as normal i/os. ? ? ? ?? ? ? ? ?- - ?? ? - ? ? ? ?? ? ? ? ? ?- - ?? - ? ?? - ? ?? ? ? ? ? a/d converter structure adrh, adrl register bit adrh adrl 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 name d11 d10 d9 d8 d7 d? d5 d4 d3 d? d1 d0 r/w r r r r r r r r r r r r por x x x x x x x x x x x x "x" ?nknown unimplemented, read as "0" d11~d0 adc conversion data HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?? ?an?a?? ??? ? 011 rev. 1.00 ?3 ?an?a?? ??? ? 011 adcr register bit 7 6 5 4 3 2 1 0 name start eocb acs3 acs? acs1 acs0 r/w r/w r r/w r/w r/w r/w por 0 1 0 0 0 0 0 0 bit 7 start : start the a/d conversion 010: start 01: reset the a/d converter and set eocb to "1" this bit is used to initiate an a/d conversion process. the bit is normally low but if set high and then cleared low again, the a/d converter will initiate a conversion process. when the bit is set high the a/d converter will be reset. bit 6 eocb : end of a/d conversion fag 0: a/d conversion ended 1: a/d conversion in progress this read only fag is used to indicate when an a/d conversion process has completed. when the conversion process is running the bit will be high. bit 5, bit 4 unimplemented, read as "0" bit 3~0 acs3, acs2, acs1, acs0 : select a/d channel 0000: an0 0001: an1 0010: an2 0011: an3 0100: an4 0101: an5 0110: an6 0111: an7 1000: an8 1001: an9 1010: an10 1011: an11 1100: an12 1101: an13 1110: an14 1111: an15 these are the a/d channel select control bits. as there is only one internal hardware a/d converter each of the eight a/d inputs must be routed to the internal converter using these bits. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?4 ?an?a?? ??? ? 011 rev. 1.00 ?5 ?an?a?? ??? ? 011 acsr register bit 7 6 5 4 3 2 1 0 name test adonb vrefs adcs? adcs1 adcs0 r/w r r/w r/w r/w r/w r/w por 1 1 0 0 0 0 bit 7 test : for test mode use only bit 6 adonb : adc module power on/off control bit 0: adc module power on 1: adc module power off this bit controls the power to the a/d internal function. this bit should be cleared to zero to enable the a/d converter. if the bit is set high then the a/d converter will be switched off reducing the device power consumption. as the a/d converter will consume a limited amount of power, even when not executing a conversion, this may be an important consideration in power sensitive battery powered applications. note: it is recommended to set adonb =1 before entering the idle/sleep mode for saving power. bit 5 unimplemented, read as "0" bit 4 vrefs : select adc reference voltage 0: v dd 1: verf pin this bit is used to select the reference voltage for the a/d converter. if the bit is high, then the a/d converter reference voltage is supplied on teh external vref pin. if the pin is low, then the internal reference is used which is taken from the pwoer supply pin v dd . bit 3 unimplemented, read as "0" bit 2~0 adcs2~adcs0 : select a/d converter clock source 000: system clock/2 001: system clock/8 010: system clock/32 011: undefned, can't be used. 100: system clock 101: system clock/4 110: system clock/16 111: undefned, can't be used. these three bits are used to select the clock source for the a/d converter. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?4 ?an?a?? ??? ? 011 rev. 1.00 ?5 ?an?a?? ??? ? 011 ancsr0 register bit 7 6 5 4 3 2 1 0 name pcr7 pcr? pcr5 pcr4 pcr3 pcr? pcr1 pcr0 r/w r/w r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 0 bit 7 pcr7 : defne pc7 is a/d input or not 0: not a/d input 1: a/d input, an7 bit 6 pcr6 : defne pc6 is a/d input or not 0: not a/d input 1: a/d input, an6 bit 5 pcr5 : defne pc1 is a/d input or not 0: not a/d input 1: a/d input, an5 bit 4 pcr4 : defne pc0 is a/d input or not 0: not a/d input 1: a/d input, an4 bit 3 pcr3 : defne pa3 is a/d input or not 0: not a/d input 1: a/d input, an3 bit 2 pcr2 : defne pa2 is a/d input or not 0: not a/d input 1: a/d input, an2 bit 1 pcr1 : defne pa1 is a/d input or not 0: not a/d input 1: a/d input, an1 bit 0 pcr0 : defne pa0 is a/d input or not 0: not a/d input 1: a/d input, an0 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?? ?an?a?? ??? ? 011 rev. 1.00 ?7 ?an?a?? ??? ? 011 ancsr1 register bit 7 6 5 4 3 2 1 0 name pcr15 pcr14 pcr13 pcr1? pcr11 pcr10 pcr9 pcr8 r/w r/w r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 0 bit 7 pcr15 : defne pe7 is a/d input or not 0: not a/d input 1: a/d input, an15 bit 6 pcr14 : defne pe6 is a/d input or not 0: not a/d input 1: a/d input, an14 bit 5 pcr13 : defne pe5 is a/d input or not 0: not a/d input 1: a/d input, an13 bit 4 pcr12 : defne pe4 is a/d input or not 0: not a/d input 1: a/d input, an12 bit 3 pcr11 : defne pe3 is a/d input or not 0: not a/d input 1: a/d input, an11 bit 2 pcr10 : defne pe2 is a/d input or not 0: not a/d input 1: a/d input, an10 bit 1 pcr9 : defne pe1 is a/d input or not 0: not a/d input 1: a/d input, an9 bit 0 pcr8 : defne pe0 is a/d input or not 0: not a/d input 1: a/d input, an8 the start bit in the register is used to start and reset the a/d converter. when the sets this bit from low to high and then low again, an analog to digital conversion cycle will be initiated. when the start bit is brought from low to high but not low again, the eocb bit in the adcr register will be set to a "1" and the analog to digital converter will be reset. it is the start bit that is used to control the overall start operation of the internal analog to digital converter . the eocb bit in the adcr register is used to indicate when the analog to digital conversion process is complete. this bit will be automatically set to "0" by the microcontroller after a conversion cycle has ended. in addition, the corresponding a/d interrupt request fag will be set in the interrupt control register, and if the interrupts are enabled, an appropriate internal interrupt signal will be generated. this a/d internal interrupt signal will direct the program flow to the associated a/d internal interrupt address for processing. if the a/d internal interrupt is disabled, the microcontroller can be used to poll the eocb bit in the adcr register to check whether it has been cleared as an alternative method of detecting the end of an a/d conversion cycle. the clock source for the a/d converter, which originates from the system clock f sys , is frst divided by a division ratio, the value of which is determined by the adcs2, adcs1 and adcs0 bits in the acsr register. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?? ?an?a?? ??? ? 011 rev. 1.00 ?7 ?an?a?? ??? ? 011 controlling the power on/off function of the a/d converter circuitry is implemented using the value of the adonb bit. although the a/d clock source is determined by the system clock f sys , and by bits adcs2, adcs1 and adcs0, there are some limitations on the maximum a/d clock source speed that can be selected. as the minimum value of permissible a/d clock period, t ad , is 0.5s, care must be taken for system clock speeds in excess of 4mhz. for system clock speeds in excess of 4mhz, the adcs2, adcs1 and adcs0 bits should not be set to "000". doing so will give a/d clock periods that are less than the minimum a/d clock period which may result in inaccurate a/d conversion values. refer to the following table for examples, where values marked with an asterisk * show where, depending upon the device, special care must be taken, as the values may be less than the specifed minimum a/d clock period. f sys a/d clock period (t ad ) adcs2, adcs1, adcs0=000 (f sys /2) adcs2, adcs1, adcs0=001 (f sys /8) adcs2, adcs1, adcs0=010 (f sys /32) adcs2, adcs1, adcs0=100 (f sys ) adcs2, adcs1, adcs0=101 (f sys /4) adcs2, adcs1, adcs0=110 (f sys /16) adcs2, adcs1, adcs0=011, 111 1mhz ? s 8 s 3? s 1 s 4 s 1? s undefned ?mhz 1 s 4 s 1? s 500ns ? s 8 s undefned 4mhz 500ns ? s 8 s 250ns* 1 s 4 s undefned 8mhz 250ns* 1 s 4 s 125ns* 500ns ? s undefned 1?mhz 167ns* ??7ns ?.?7 s 83ns* 333ns* 1 s undefned a/d clock period examples a/d input pins all of the a/d analog input pins are pin-shared with the i/o pins on port a, port c and port e. bits pcr15~pcr0 in the ancsr0 and ancsr1 registers, determine whether the input pins are setup as normal input/output pins or whether they are setup as analog inputs. in this way, pins can be changed under program control to change their function from normal i/o operation to analog inputs and vice versa. pull-high resistors, which are setup through register programming, apply to the input pins only when they are used as normal i/o pins, if setup as a/d inputs the pull-high resistors will be automatically disconnected. note that it is not necessary to frst setup the a/d pin as an input in the pac, pcc and pec port control registers to enable the a/d input as when the pcr15~pcr0 bits enable an a/d input, the status of the port control register will be overridden. summary of a/d conversion steps the following summarises the individual steps that should be ex ecuted in order to implement an a/ d conversion process. step 1 select the required a/d conversion clock by correctly programming bits adcs2, adcs1 and adcs0 in the register. step 2 select which pins are to be used as a/d inputs and confgure them as a/d input pins by correctly programming the pcr15~pcr0 bits in the ancsr0, ancsr1 registers. step 3 enable the a/d by clearing the adonb in the acsr register to zero. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?8 ?an?a?? ??? ? 011 rev. 1.00 ?9 ?an?a?? ??? ? 011 step 4 select which channel is to be connected to the internal a/d converter by correctly programming the acs3~acs0 bits which are also contained in the register. step 5 if the interrupts are to be used, the interrupt control registers must be correctly confgured to ensure the a/d converter interrupt function is active. the master interrupt control bit, emi, the intc0 interrupt control register must be set to 1, the a/d converter interrupt bit, ade, must also be set to 1. step 6 the analog to digital conversion process can now be initialised by setting the start bit in the adcr register from 0 to 1 and then to 0 again. note that this bit should have been originally set to 0. step 7 to check when the analog to digital conversion process is complete, the eocb bit in the adcr register can be polled. the conversion process is complete when this bit goes low. when this occurs the a/d data registers adrl and adrh can be read to obtain the conversion value. as an alternative method if the interrupts are enabled and the stack is not full, the program can wait for an a/d interrupt to occur. note: when checking for the end of the conversion process, if the method of polling the eocb bit in the adcr register is used, the interrupt enable step above can be omitted. the accompanying diagram shows graphically the various stages involved in an analog to digital conversion process and its associated timing. the setting up and operation of the a/d converter function is fully under the control of the application program as there are no confguration options associated with the a/d converter. after an a/d conversion process has been initiated by the application program, the microcontroller internal hardware will begin to carry out the conversion, during which time the program can continue with other functions. the time taken for the a/d conversion is 16t ad where t ad is equal to the a/d clock period. programming considerations when programming, special attention must be given to the pcr[15:0] bits in the register. if these bits are all cleared to zero no external pins will be selected for use as a/d input pins allowing the pins to be used as normal i/o pins. when this happens the internal a/d circuitry will be power down. setting the adonb bit high has the ability to power down the internal a/d circuitry, which may be an important consideration in power sensitive applications. a/d transfer function as the device contain a 12-bit a/d converter, its full-scale converted digitised value is equal to fffh. since the full-scale analog input value is equal to the v dd voltage, this gives a single bit analog input value of v dd /4096. the diagram show the ideal transfer function between the analog input value and the digitised output value for the a/d converter. note that to reduce the quantisation error, a 0.5 lsb offset is added to the a/d converter input. except for the digitised zero value, the subsequent digitised values will change at a point 0.5 lsb below where they would change without the offset, and the last full scale digitised value will change at a point 1.5 lsb below the v dd level. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 ?8 ?an?a?? ??? ? 011 rev. 1.00 ?9 ?an?a?? ??? ? 011 a/d programming example the following two programming examples illustrate how to setup and implement an a/d conversion. in the frst example, the method of polling the eocb bit in the adcr register is used to detect when the conversion cycle is complete, whereas in the second example, the a/d interrupt is used to determine when the conversion is complete. ?? ? ? ? ??? ? ? ? ? ? - ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ?? ? ? ? ? ? a/d conversion timing ? ? ? ? ? ? ?? ? ? ideal a/d transfer function HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 70 ?an?a?? ??? ? 011 rev. 1.00 71 ?an?a?? ??? ? 011 example: using an eocb polling method to detect the end of conversion clr eadi ; disable adc interrupt mov a,00000001b mov acsr,a ; select f sys /8 as a/d clock and adonb=0 mov a,0fh ; setup ancsr0 and ancsr1 to confgure pins an0~an3 mov ancsr0,a mov a, 00h mov ancsr1,a ; mov a,00000000b ; mov adcr,a ; select an0 to be connected to the a/d converter : start_conversion: clr start set start ; reset a/d clr start ; start a/d polling_eoc: sz eocb ; poll the adcr register eocb bit to detect end ; of a/d conversion jmp polling_eoc ; continue polling mov a,adrl ; read low byte conversion result value mov adrl_buffer,a ; save result to user defned register mov a,adrh ; read high byte conversion result value mov adrh_buffer,a ; save result to user defned register : jmp start_conversion; start next a/d conversion note: to power off adc module, it is necessary to set adonb as "1". HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 70 ?an?a?? ??? ? 011 rev. 1.00 71 ?an?a?? ??? ? 011 example: using the interrupt method to detect the end of conversion clr eadi ; disable adc interrupt mov a,00000001b mov acsr,a ; select f sys /8 as a/d clock and adonb=0 mov a,0fh ; setup ancsr0 and ancsr1 to confgure pins an0~an3 mov ancsr0,a mov a, 00h mov ancsr1,a ; mov a,00000000b ; mov adcr, a ; select an0 to be connected to the a/d converter : start_conversion: clr start set start ; reset a/d clr start ; start a/d clr adf ; clear adc interrupt request fag set eadi ; enable adc interrupt set emi ; enable global interrupt : : ; adc interrupt service routine adc_: mov acc_stack,a ; save acc to user defned memory mov a,status mov status_stack,a ; save status to user defned memory : : mov a,adrl ; read low byte conversion result value mov adrl_buffer,a ; save result to user defned register mov a,adrh ; read high byte conversion result value mov adrh_buffer,a ; save result to user defned register : : exit_isr: mov a,status_stack mov status,a ; restore status from user defned memory mov a,acc_stack ; restore acc from user defned memory clr adf ; clear adc interrupt fag reti note: to power off adc module, it is necessary to set adonb as "1". HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 7? ?an?a?? ??? ? 011 rev. 1.00 73 ?an?a?? ??? ? 011 interrupts interrupts are an important part of any microcontroller system. when an external event or an internal function such as a timer/event counter or time base requires microcontroller attention, their corresponding interrupt will enforce a temporary suspension of the main program allowing the microcontroller to direct attention to their respective needs. the device contains a single external interrupt and multiple internal interrupts. the external interrupt is controlled by the action of the external interrupt pin, while the internal interrupts are generated by the various functions such as timer/event counters, and time base. interrupt register overall interrupt control, which means interrupt enabling and request fag setting, is controlled by using two registers, intc0 and intc1. by controlling the appropriate enable bits in this registers each individual interrupt can be enabled or disabled. also when an interrupt occurs, the corresponding request fag will be set by the microcontroller. the global enable fag if cleared to zero will disable all interrupts. intc0 register bit 7 6 5 4 3 2 1 0 name t1f t0f eif et1i et0i eei emi r/w r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 bit 7 unimplemented, read as 0 bit 6 t1f : timer/event counter 1 interrupt request fag 0: inactive 1: active bit 5 t0f : timer/event counter 0 interrupt request fag 0: inactive 1: active bit 4 eif : external interrupt request fag 0: inactive 1: active bit 3 et1i : timer/event counter 1 interrupt enable 0: disable 1: enable bit 2 et0i : timer/event counter 0 interrupt enable 0: disable 1: enable bit 1 eei : external interrupt enable 0: disable 1: enable bit 0 emi : master interrupt global enable 0: disable 1: enable HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 7? ?an?a?? ??? ? 011 rev. 1.00 73 ?an?a?? ??? ? 011 intc1 register bit 7 6 5 4 3 2 1 0 name mff adf t?f emfi eadi et?i r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 %lw xqlpsohphqwhguhdgdv bit 6 mff 0xowlixfwlrlwhuuxswuhtxhvwd 0: ina fyh dfyh bit 5 adf frhuwh ulwhuuxswuhtxhvwd dfyh dfyh bit 4 t2f 7lphuhwrxwhulwhuuxswuhtxhvwd dfyh dfyh sohhhhddv bit 2 emfi 0xowlixfwlrlwhuuxswhdeoh vdeoh hdeoh bit 1 eadi frhuwhulwhuuxswhdeoh vdeoh hdeoh bit 0 et2i 7lphuhwrxwhulwhuuxswhdeoh vdeoh hdeoh mfic register bit 7 6 5 4 3 2 1 0 name sif simf tbf esii esim etbi r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 %lw xqlpsohphqwhguhdgdv bit 6 sif 63,lwhuuxswuhtxhvwd dfyh dfyh bit 5 simf 6,0lwhuuxswuhtxhvwd dfyh dfyh bit 4 tbf 7lphdvhlwhuuxswuhtxhvwd 0 dfyh dfyh sohhhhddv bit 2 esii 63,lwhuuxswhdeoh vdeoh hdeoh bit 1 esim 6,0lwhuuxswhdeoh vdeoh hdeoh bit 0 etbi 7lphdvhlwhuuxswhdeoh vdeoh hdeoh HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 74 ?an?a?? ??? ? 011 rev. 1.00 75 ?an?a?? ??? ? 011 interrupt operation a timer/event counter overflow, an active edge on the external interrupt pin, a serial data byte transmitted or received completion, or a time base event will all generate an interrupt request by setting their corresponding request flag, if their appropriate interrupt enable bit is set. when this happens, the program counter, which stores the address of the next instruction to be executed, will be transferred onto the stack. the program counter will then be loaded with a new address which will be the value of the corresponding interrupt vector. the microcontroller will then fetch its next instruction from this interrupt vector. the instruction at this vector will usually be a jmp statement which will jump to another section of program which is known as the interrupt service routine. here is located the code to control the appropriate interrupt. the interrupt service routine must be terminated with a reti instruction, which retrieves the original program counter address from the stack and allows the microcontroller to continue with normal execution at the point where the interrupt occurred. the various interrupt enable bits, together with their associated request flags, are shown in the following diagram with their order of priority. ? ? ? ? ? ? ? ? ? ? ? - ? ?? ? - ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? - ? ? ? ? ? once an interrupt subroutine is serviced, all the other interru pts will be blocked, as the emi bit will be cleared automatically. this will prevent any further interrupt nesting from occurring. however, if other interrupt requests occur during this interval, although the interrupt will not be immediately serviced, the request flag will still be recorded. if an interrupt requires immediate servicing while the program is already in another interrupt service routine, the emi bit should be set after entering the routine, to allow interrupt nesting. if the stack is full, the interrupt request will not be acknowledged, even if the related interrupt is enabled, until the stack pointer is decremented. if immediate service is desired, the stack must be prevented from becoming full. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 74 ?an?a?? ??? ? 011 rev. 1.00 75 ?an?a?? ??? ? 011 when an interrupt request is generated it takes 2 or 3 instruction cycle before the program jumps to the interrupt vector. if the device is in the sleep or idle mode and is woken up by an interrupt request then it will take 3 cycles before the program jumps to the interrupt vector . wait fo? ? ~ 3 inst??ction c?cles main p?og?am isr ent?? enable bit set ? main p?og?am reti ( it will set emi a?tomaticall? ) a?tomaticall? disable inte???pt clea? emi & req?est flag n y interrupt flow interrupt priority interrupts, occurring in the interval between the rising edges of two consecutive t2 pulses, will be serviced on the latter of the two t2 pulses, if the corresponding interrupts are enabled. in case of simultaneous requests, the following table shows the priority that is applied. these can be masked by resetting the emi bit. interrupt source priority vector exte?nal inte???pt 1 04h timer/event counter 0 overfow ? 08h timer/event counter 1 overfow 3 0ch timer/event counter 2 overfow 4 10h a/d inte???pt 5 14h m?lti-f?nction inte???pt (time base ? sim? spia) ? 18h in cases where both external and internal interrupts are enabled and where an external and internal interrupt occurs simultaneously, the external interrupt will always have priority and will therefore be serviced first. suitable masking of the individual interrupts using the interrupt registers can prevent simultaneous occurrences. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 7? ?an?a?? ??? ? 011 rev. 1.00 77 ?an?a?? ??? ? 011 external interrupt for an external interrupt to occur, the global interrupt enable bit, emi, and external interrupt enable bit, inte, must frst be set. an actual external interrupt will take place when the external interrupt request fag, intf, is set, a situation that will occur when an edge transition appears on the external int line. the type of transition that will trigger an external interrupt, whether high to low, low to high or both is determined by the integ0 and integ1 bits, which are bits 6 and 7 respectively, in the ctrl1 control register. these two bits can also disable the external interrupt function. integ1 integ0 edge trigger type 0 0 exte?nal inte???pt disable 0 1 rising edge t ?igge? 1 0 falling edge t ?igge? 1 1 both edge t ?igge? the external interrupt pin is pin-shared with the i/o pin pa3 and can only be confgured as an external interrupt pin if the corresponding external interrupt enable bit in the intc0 register has been set and the edge trigger type has been selected using the ctrl1 register. the pin must also be setup as an input by setting the corresponding pac.3 bit in the port control register. when the interrupt is enabled, the stack is not full and an active transition appears on the external interrupt pin, a subroutine call to the external interrupt vector at location 04h, will take place. when the interrupt is serviced, the external interrupt request fag, eif, will be automatically reset and the emi bit will be automatically cleared to disable other interrupts. note that any pull-high resistor connections on this pin will remain valid even if the pin is used as an external interrupt input. timer/event counter interrupt for a timer/event counter interrupt to occur, the global interrupt enable bit, emi, and the corresponding timer interrupt enable bit, tne, must first be set. an actual timer/event counter interrupt will take place when the timer/event counter request fag, tnf, is set, a situation that will occur when the relevant timer/event counter overfows. when the interrupt is enabled, the stack is not full and a timer/event counter n overflow occurs, a subroutine call to the relevant timer interrupt vector, will take place. when the interrupt is serviced, the timer interrupt request fag, tnf, will be automatically reset and the emi bit will be automatically cleared to disable other interrupts. multi-function interrupt unlike the other independent interrupts, the multi-function interrupt has no independent source, but rather is formed from other existing interrupt sources, namely the time-base interrupt, sim interrupt and spia interrupt. a multi-function interrupt request will take place when the multi- function interrupt request fag, mff is set. the multi-function interrupt fag will be set when any of their included functions generate an interrupt request fag. to allow the program to branch to its respective interrupt vector address, when the multi-function interrupt is enabled and the stack is not full, and either one of the interrupts contained within each of multi-function interrupt occurs, a subroutine call to the multi-function interrupt vector will take place. when the interrupt is serviced, the multi-function interrupt request fag will be automatically reset and the emi bit will be automatically cleared to disable other interrupts. however, it must be noted that, although the multi-function interrupt fag will be automatically reset when the interrupt is serviced, the request flags from the original source of the multi-function interrupt, namely the time-base interrupt, sim interrupt and spia interrupt will not be automatically reset and must be manually reset by the application program. after a multi-function has been generated, the application program can determine which interrupt source has occurred by interrogating the interrupt request flags, sif, simf or tbf within the mfic register. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 7? ?an?a?? ??? ? 011 rev. 1.00 77 ?an?a?? ??? ? 011 programming considerations by disabling the relevant interrupt enable bits, a requested interrupt can be prevented from being serviced, however, once an interrupt request flag is set, it will re- main in this condition in the interrupt register until the corresponding interrupt is serviced or until the request fag is cleared by the application program. where a certain interrupt is contained within the multi-function interrupt, then when the interrupt service routine is executed, as only the multi-function interrupt request fag, mff, will be automatically cleared, the individual request fag for the function needs to be cleared by the application program. it is recommended that programs do not use the call instruction within the interrupt service subroutine. interrupts often occur in an unpredictable manner or need to be serviced immediately. if only one stack is left and the interrupt is not well controlled, the original control sequence will be damaged once a call subroutine is executed in the interrupt subroutine. every interrupt has the capability of waking up the microcontroller when it is in sleep or idle mode, the wake up being generated when the interrupt request fag changes from low to high. if it is required to prevent a certain interrupt from waking up the microcontroller then its respective request fag should be frst set high before entering the sleep or idle mode. as only the program counter is pushed onto the stack, then when the interrupt is serviced, if the contents of the accumulator, status register or other registers are altered by the interrupt service program, their contents should be saved to the memory at the beginning of the interrupt service routine. to return from an interrupt subroutine, either a ret or reti instruction may be executed. the reti instruction in addition to executing a return to the main program also automatically sets the emi bit high to allow further interrupts. the ret instruction however only executes a return to the main program leaving the emi bit in its present zero state and therefore disabling the execution of further interrupts. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 78 ?an?a?? ??? ? 011 rev. 1.00 79 ?an?a?? ??? ? 011 lcd scom function the devices have the capability of driving external lcd panels. the common pins for lcd driving, scom0~scom3, are pin shared with the pb0~ pb3 pins. the lcd signals, com and seg, are generated using the application program. lcd operation an external lcd panel can be driven using this device by configuring the pb0~pb3 pins as common pins and using other output ports lines as segment pins. the lcd driver function is controlled using the scomc register which in addition to controlling the overall on/off function also controls the bias voltage setup function. this enables the lcd com driver to generate the necessaryv dd /2 voltage levels for lcd 1/2 bias operation. the scomen bit in the scomc register is the overall master control for the lcd driver, however this bit is used in conjunction with the comnen bits to select which port b pins are used for lcd driving. note that the port control register does not need to frst setup the pins as outputs to enable the lcd driver operation. scom circuit scomen comnen pin function o/p level 0 x i/o 0 o? 1 1 0 i/o 0 o? 1 1 1 scomn v dd /? output control HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 78 ?an?a?? ??? ? 011 rev. 1.00 79 ?an?a?? ??? ? 011 lcd bias control the lcd com driver enables a range of selections to be provided to suit the requirement of the lcd panel which is being used. the bias resistor choice is implemented using the isel1 and isel0 bits in the scomc register. scomc register bit 7 6 5 4 3 2 1 0 name isel1 isel0 scomen com3en com?en com1en com0en r/w r/w r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 0 bit 7 reserved bit 1: unpredictable operation - bit must not be set high 0: correct level - bit must be reset to zero for correct operation bit 6,5 : scom operating current selection (v dd =5v) 00: 25a 01: 50a 10: 100a 11: 200a bit 4 some : scom module on/off control 0: disable 1: enable scomn can be enable by comnen if scomen=1 bit 3 om3e : pb3 or scom3 selection 0: i/o 1: scom3 bit 2 om2e : pb2 or scom2 selection 0: i/o 1: scom2 bit 1 om1e : pb1 or scom1 selection 0: i/o 1: scom1 bit 0 om0e : pb0 or scom0 selection 0: i/o 1: scom0 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 80 ?an?a?? ??? ? 011 rev. 1.00 81 ?an?a?? ??? ? 011 serial interface module C sim these devices contain a serial interface module, which includes both the four line spi interface or the two line i 2 c interface types, to allow an easy method of communication with external peripheral hardware. having relatively simple communication protocols, these serial interface types allow the microcontroller to interface to external spi or i 2 c based hardware such as sensors, flash or eeprom memory, etc. the sim interface pins are pin-shared with other i/o pins therefore the sim interface function must frst be selected using a confguration option. as both interface types share the same pins and registers, the choice of whether the spi or i 2 c type is used is made using the sim operating mode control bits, named sim2~sim0, in the simc0 register. these pull-high resistors of the sim pin-shared i/o are selected using pull-high control registers, and also if the sim function is enabled. spi interface this spi interface function which is part of the serial interface module, should not be confused with the other independent spi function, known as spia, which is described in another section of this datasheet. the spi interface is often used to communicate with external peripheral devices such as sensors, flash or eeprom memory devices etc. originally developed by motorola, the four line spi interface is a synchronous serial data interface that has a relatively simple communication protocol simplifying the programming requirements when communicating with external hardware devices. the communication is full duplex and operates as a slave/master type, where the device can be either master or slave. although the spi interface specifcation can control multiple slave devices from a single master, but this device provided only one scs pin. if the master needs to control multiple slave devices from a single master, the master can use i/o pin to select the slave devices. spi interface operation the spi interface is a full duplex synchronous serial data link. it is a four line interface with pin names sdi, sdo, sck and scs . pins sdi and sdo are the serial data input and serial data output lines, sck is the serial clock line and scs is the slave select line. as the spi interface pins are pin-shared with normal i/o pins and with the i 2 c function pins, the spi interface must frst be enabled by selecting the sim enable confguration option and setting the correct bits in the simc0 and simc2 registers. after the spi confguration option has been confgured it can also be additionally disabled or enabled using the simen bit in the simc0 register. communi - cation between devices connected to the spi interface is carried out in a slave/master mode with all data transfer initiations being implemented by the master. the master also controls the clock signal. as the device only contains a single scs pin only one slave device can be utilized. the scs pin is controlled by software, set csen bit to " 1 " to enable scs pin function, set csen bit to " 0 " the scs pin will be foating state. spi master/slave connection HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 80 ?an?a?? ??? ? 011 rev. 1.00 81 ?an?a?? ??? ? 011 ? ? ? ? ? ? ? ? ? ?? - ? ? ? ? ? ? ? ? ?? ? ? ? ? spi block diagram the spi function in this device offers the following features: full duplex synchronous data transferboth master and slave modes lsb frst or msb frst data transmission modes transmission complete fag rising or falling active clock edge wcol and csen bit enabled or disable select the status of the spi interface pins is determined by a number of factors such as whether the device is in the master or slave mode and upon the condition of certain control bits such as csen and simen. there are several configuration options associated with the spi interface. one of these is to enable the sim function which selects the sim pins rather than normal i/o pins. note that if the confguration option does not select the sim function then the simen bit in the simc0 register will have no effect. another two spi confguration options determine if the csen and wcol bits are to be used. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 8? ?an?a?? ??? ? 011 rev. 1.00 83 ?an?a?? ??? ? 011 spi registers there are three internal registers which control the overall operation of the spi interface. these are the simd data register and two registers simc0 and simc2. note that the simc1 register is only used by the i 2 c interface. register name bit 7 6 5 4 3 2 1 0 simc0 sim? sim1 sim0 pcken pckp1 pckp0 simen simd d7 d? d5 d4 d3 d? d1 d0 simc? d7 d? ckpolb ckeg mls csen wcol trf sim registers list the simd register is used to store the data being transmitted and received. the same register is used by both the spi and i 2 c functions. before the device writes data to the spi bus, the actual data to be transmitted must be placed in the simd register. after the data is received from the spi bus, the device can read it from the simd register. any transmission or reception of data from the spi bus must be made via the simd register. simd regisater bit 7 6 5 4 3 2 1 0 name d7 d? d5 d4 d3 d? d1 d0 r/w r/w r/w r/w r/w r/w r/w r/w r/w por x x x x x x x x " x " ?nknown there are also two control registers for the spi interface, simc0 and simc2. note that the simc2 register also has the name sima which is used by the i 2 c function. the simc1 register is not used by the spi function, only by the i 2 c function. register simc0 is used to control the enable/ disable function and to set the data transmission clock frequency. although not connected with the spi function, the simc0 register is also used to control the peripheral clock prescaler. register simc2 is used for other control functions such as lsb/msb selection, write collision fag etc. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 8? ?an?a?? ??? ? 011 rev. 1.00 83 ?an?a?? ??? ? 011 simc0 register bit 7 6 5 4 3 2 1 0 name sim? sim1 sim0 pcken pckp1 pckp0 simen r/w r/w r/w r/w r/w r/w r/w r/w por 1 1 1 0 0 0 0 bit 7~5 sim2, sim1, sim0 : sim operating mode control 000: spi master mode; spi clock is f sys /4 001: spi master mode; spi clock is f sys /16 010: spi master mode; spi clock is f sys /64 011: spi master mode; spi clock is f lxt 100: spi master mode; spi clock is timer/event counter 0 output/2 (pfd0) 101: spi slave mode 110: i 2 c slave mode 111: unused mode these bits setup the overall operating mode of the sim function. as well as selecting if the i 2 c or spi function, they are used to control the spi master/slave selection and the spi master clock frequency. the spi clock is a function of the system clock but can also be chosen to be sourced from the timer/event counter 0. if the spi slave mode is selected then the clock will be supplied by an external master device. bit 4 pcken : peripheral clock pin control described elsewhere. bit 3~2 pckp1, pckp0 : select pck output pin frequency described elsewhere. bit 1 simen : sim control 0: disable 1: enable the bit is the overall on/off control for the sim interface. when the simen bit is cleared to zero to disable the sim interface, the sdi, sdo, sck and scs , or sda and scl lines will be in a foating condition and the sim operating current will be reduced to a minimum value. when the bit is high the sim interface is enabled. the sim confguration option must have frst enabled the sim interface for this bit to be effective. if the sim is confgured to operate as an spi interface via the sim2~sim0 bits, the contents of the spi control registers will remain at the previous settings when the simen bit changes from low to high and should therefore be frst initialised by the application program. if the sim is confgured to operate as an i 2 c interface via the sim2~sim0 bits and the simen bit changes from low to high, the contents of the i 2 c control bits such as htx and txak will remain at the previous settings and should therefore be frst initialised by the application program while the relevant i 2 c fags such as hcf, haas, hbb, srw and rxak will be set to their default states. bit 0 unimplemented, read as " 0 " HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 84 ?an?a?? ??? ? 011 rev. 1.00 85 ?an?a?? ??? ? 011 simc2 register bit 7 6 5 4 3 2 1 0 name d7 d? ckpolb ckeg mls csen wcol trf r/w r/w r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 0 bit 7~6 undefned bit this bit can be read or written by user software program. bit 5 ckpolb : determines the base condition of the clock line 0: the sck line will be high when the clock is inactive 1: the sck line will be low when the clock is inactive the ckpolb bit determines the base condition of the clock line, if the bit is high, then the sck line will be low when the clock is inactive. when the ckpolb bit is low, then the sck line will be high when the clock is inactive. bit 4 ckeg : determines spi sck active clock edge type ckpolb=0 0: sck is high base level and data capture at sck rising edge 1: sck is high base level and data capture at sck falling edge ckpolb=1 0: sck is low base level and data capture at sck falling edge 1: sck is low base level and data capture at sck rising edge the ckeg and ckpolb bits are used to setup the way that the clock signal outputs and inputs data on the spi bus. these two bits must be confgured before data transfer is executed otherwise an erroneous clock edge may be generated. the ckpolb bit determines the base condition of the clock line, if the bit is high, then the sck line will be low when the clock is inactive. when the ckpolb bit is low, then the sck line will be high when the clock is inactive. the ckeg bit determines active clock edge type which depends upon the condition of ckpolb bit. bit 3 mls : spi data shift order 0: lsb 1: msb this is the data shift select bit and is used to select how the data is transferred, either msb or lsb frst. setting the bit high will select msb frst and low for lsb frst. bit 2 csen : spi scs pin control 0: disable 1: enable the csen bit is used as an enable/disable for the scs pin. if this bit is low, then the scs pin will be disabled and placed into a floating condition. if the bit is high the scs pin will be enabled and used as a select pin. note that using the csen bit can be disabled or enabled via confguration option. bit 1 wcol : spi write collision fag 0: no collision 1: collision the wcol fag is used to detect if a data collision has occurred. if this bit is high it means that data has been attempted to be written to the simd register during a data transfer operation. this writing operation will be ignored if data is being transferred. the bit can be cleared by the application program. note that using the wcol bit can be disabled or enabled via confguration option. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 84 ?an?a?? ??? ? 011 rev. 1.00 85 ?an?a?? ??? ? 011 bit 0 trf : spi transmit/receive complete fag 0: data is being transferred 1: spi data transmission is completed the trf bit is the transmit/receive complete fag and is set "1" automatically when an spi data transmission is completed, but must set to "0" by the application program. it can be used to generate an interrupt. spi communication after the spi interface is enabled by setting the simen bit high, then in the master mode, when data is written to the simd register, transmission/reception will begin simultaneously. when the data transfer is complete, the trf fag will be set automatically, but must be cleared using the application program. in the slave mode, when the clock signal from the master has been received, any data in the simd register will be transmitted and any data on the sdi pin will be shifted into the simd register. the master should output an scs signal to enable the slave device before a clock signal is provided. the slave data to be transferred should be well prepared at the appropriate moment relative to the scs signal depending upon the configurations of the ckpolb bit and ckeg bit. the accompanying timing diagram shows the relationship between the slave data and scs signal for various confgurations of the ckpolb and ckeg bits. the spi will continue to function even in the idle mode. ? ? ? ? ? ?? ?? ? ?? ? ?? ?? -? ?? ?? ?? ?? ?? -? ?? ? ?? ?? ? ?? ?? ?? ? ?? ? ?? ?? -? ?? ?? ?? ?? ?? -? ?? ? ?? ?? ? ?? ? ? ? spi master mode timing ? ? ? ? ??? ? - ? ? ?? spi slave mode timing - ckeg=0 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 8? ?an?a?? ??? ? 011 rev. 1.00 87 ?an?a?? ??? ? 011 ? ??? ? ? ? ? ? ? ?? ?? ? - ? ?? ?? ? ? ?? ? ? ? ? ? ? ? ?? ?? ?? ? ? ?? ?? ??? ? ?? ? ? ? ? ? ? ?? spi slave mode timing - ckeg=1 ? ? ? ? ? ? ? ? ? ? ? - ? ?? ? ? ? ? ? ? ?? ?? ? ?? ? ??? ??? ? ?? ? ?? ?? ? spi transfer control flowchart HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 8? ?an?a?? ??? ? 011 rev. 1.00 87 ?an?a?? ??? ? 011 i 2 c interface the i 2 c interface is used to communicate with external peripheral devices such as sensors, eeprom memory etc. originally developed by philips, it is a two line low speed serial interface for synchronous serial data transfer. the advantage of only two lines for communication, relatively simple communication protocol and the ability to accommodate multiple devices on the same bus has made it an extremely popular interface type for many applications. i 2 c mater slave bus connection i 2 c interface operation the i 2 c serial interface is a two line interface, a serial data line, sda, and serial clock line, scl. as many devices may be connected together on the same bus, their outputs are both open drain types. for this reason it is necessary that external pull-high resistors are connected to these outputs. note that no chip select line exists, as each device on the i 2 c bus is identified by a unique address which will be transmitted and received on the i 2 c bus. when two devices communicate with each other on the bidirectional i 2 c bus, one is known as the master device and one as the slave device. both master and slave can transmit and receive data, however, it is the master device that has overall control of the bus. for these devices, which only operates in slave mode, there are two methods of transferring data on the i 2 c bus, the slave transmit mode and the slave receive mode. there are several configuration options associated with the i 2 c interface. one of these is to enable the function which selects the sim pins rather than normal i/o pins. note that if the confguration option does not select the sim function then the simen bit in the simc0 register will have no effect. a confguration option exists to allow a clock other than the system clock to drive the i 2 c interface. another confguration option determines the debounce time of the i 2 c interface. this uses the internal clock to in effect add a debounce time to the external clock to reduce the possibility of glitches on the clock line causing erroneous operation. the debounce time, if selected, can be chosen to be either 1 or 2 system clocks. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 88 ?an?a?? ??? ? 011 rev. 1.00 89 ?an?a?? ??? ? 011 send slave add?ess and r/w bit f?om maste? start signal f?om maste? acknowledge f?om slave send data b?te f?om maste? acknowledge f?om slave stop signal f?om maste? i 2 c registers there are three control registers associated with the i 2 c bus, simc0, simc1 and sima and one data register, simd. the simd register, which is shown in the above spi section, is used to store the data being transmitted and received on the i 2 c bus. before the microcontroller writes data to the i 2 c bus, the actual data to be transmitted must be placed in the simd register. after the data is received from the i 2 c bus, the microcontroller can read it from the simd register. any transmission or reception of data from the i 2 c bus must be made via the simd register. note that the sima register also has the name simc2 which is used by the spi function. bit simen and bits sim2~sim0 in register simc0 are used by the i 2 c interface. register name bit 7 6 5 4 3 2 1 0 simc0 sim? sim1 sim0 pcken pckp1 pckp0 simen simc1 hcf haas hbb htx txak srw iamwu rxak simd d7 d? d5 d4 d3 d? d1 d0 sima iica? iica5 iica4 iica3 iica? iica1 iica0 d0 i 2 c registers list HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 88 ?an?a?? ??? ? 011 rev. 1.00 89 ?an?a?? ??? ? 011 simc0 register bit 7 6 5 4 3 2 1 0 name sim? sim1 sim0 pcken pckp1 pckp0 simen r/w r/w r/w r/w r/w r/w r/w r/w por 1 1 1 0 0 0 0 bit 7~5 sim2, sim1, sim0 : sim operating mode control 000: spi master mode; spi clock is f sys /4 001: spi master mode; spi clock is f sys /16 010: spi master mode; spi clock is f sys /64 011: spi master mode; spi clock is f lxt 100: spi master mode; spi clock is timer/event counter 0 output/2 (pfd0) 101: spi slave mode 110: i 2 c slave mode 111: unused mode these bits setup the overall operating mode of the sim function. as well as selecting if the i 2 c or spi function, they are used to control the spi master/slave selection and the spi master clock frequency. the spi clock is a function of the system clock but can also be chosen to be sourced from timer/event counter 0. if the spi slave mode is selected then the clock will be supplied by an external master device. bit 4 pcken : peripheral clock pin control described elsewhere. bit 3~2 pckp1, pckp0 : select pck output pin frequency described elsewhere. bit 1 simen : sim control 0: disable 1: enable the bit is the overall on/off control for the sim interface. when the simen bit is cleared to zero to disable the sim interface, the sdi, sdo, sck and scs , or sda and scl lines will be in a foating condition and the sim operating current will be reduced to a minimum value. when the bit is high the sim interface is enabled. the sim confguration option must have frst enabled the sim interface for this bit to be effective. if the sim is confgured to operate as an spi interface via sim2~sim0 bits, the contents of the spi control registers will remain at the previous settings when the simen bit changes from low to high and should therefore be frst initialised by the application program. if the sim is confgured to operate as an i 2 c interface via the sim2~sim0 bits and the simen bit changes from low to high, the contents of the i 2 c control bits such as htx and txak will remain at the previous settings and should therefore be frst initialised by the application program while the relevant i 2 c fags such as hcf, haas, hbb, srw and rxak will be set to their default states. bit 0 unimplemented, read as " 0 " HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 90 ?an?a?? ??? ? 011 rev. 1.00 91 ?an?a?? ??? ? 011 simc1 register bit 7 6 5 4 3 2 1 0 name hcf haas hbb htx txak srw iamwu rxak r/w r r r r/w r/w r r/w r por 1 0 0 0 0 0 0 1 bit 7 hcf : i 2 c bus data transfer completion fag 0: data is being transferred 1: completion of an 8-bit data transfer the hcf fag is the data transfer fag. this fag will be zero when data is being transferred. upon completion of an 8-bit data transfer the fag will go high and an interrupt will be generated. bit 6 haas : i 2 c bus address match fag 0: not address match 1: address match the hass fag is the address match fag. this fag is used to determine if the slave device address is the same as the master transmit address. if the addresses match then this bit will be high, if there is no match then the fag will be low . bit 5 hbb : i 2 c bus busy fag 0: i 2 c bus is not busy 1: i 2 c bus is busy the hbb fag is the i 2 c busy fag. this fag will be " 1 " when the i 2 c bus is busy which will occur when a start signal is detected. the fag will be set to " 0 " when the bus is free which will occur when a stop signal is detected. bit 4 htx : select i 2 c slave device is transmitter or receiver 0: slave device is the receiver 1: slave device is the transmitter bit 3 txak : i 2 c bus transmit acknowledge fag 0: slave send acknowledge fag 1: slave do not send acknowledge fag the txak bit is the transmit acknowledge fag. after the slave device receipt of 8-bits of data, this bit will be transmitted to the bus on the 9th clock from the slave device. the slave device must always set txak bit to " 0 " before further data is received. bit 2 srw : i 2 c slave read/write fag 0: slave device should be in receive mode 1: slave device should be in transmit mode the srw fag is the i 2 c slave read/write fag. this fag determines whether the master device wishes to transmit or receive data from the i 2 c bus. when the trans - mitted address and slave address is match, that is when the haas fag is set high, the slave device will check the srw flag to determine whether it should be in transmit mode or receive mode. if the srw fag is high, the master is requesting to read data from the bus, so the slave device should be in transmit mode. when the srw fag is zero, the master will write data to the bus, therefore the slave device should be in receive mode to read this data. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 90 ?an?a?? ??? ? 011 rev. 1.00 91 ?an?a?? ??? ? 011 bit 1 iamwu : i 2 c address match wake-up control 0: disable 1: enable this bit should be set to " 1 " to enable i 2 c address match wake up from sleep or idle mode. bit 0 rxak : i 2 c bus receive acknowledge fag 0: slave receive acknowledge fag 1: slave do not receive acknowledge fag the rxak fag is the receiver acknowledge fag. when the rxak fag is " 0 " , it means that a acknowledge signal has been received at the 9th clock, after 8 bits of data have been transmitted. when the slave device in the transmit mode, the slave device checks the rxak fag to determine if the master receiver wishes to receive the next byte. the slave transmitter will therefore continue sending out data until the rxak fag is " 1 " . when this occurs, the slave transmitter will release the sda line to allow the master to send a stop signal to release the i 2 c bus. the simd register is used to store the data being transmitted and received. the same register is used by both the spi and i 2 c functions. before the device writes data to the spi bus, the actual data to be transmitted must be placed in the simd register. after the data is received from the spi bus, the device can read it from the simd register. any transmission or reception of data from the spi bus must be made via the simd register. simd register bit 7 6 5 4 3 2 1 0 name d7 d? d5 d4 d3 d? d1 d0 r/w r/w r/w r/w r/w r/w r/w r/w r/w por x x x x x x x x " x " ?nknown sima register bit 7 6 5 4 3 2 1 0 name iica? iica5 iica4 iica3 iica? iica1 iica0 r/w r/w r/w r/w r/w r/w r/w r/w por x x x x x x x " x " ?nknown bit 7~1 iica6~ iica0 : i 2 c slave address iica6~ iica0 is the i 2 c slave address bit 6~ bit 0. the sima register is also used by the spi interface but has the name simc2. the sima register is the location where the 7-bit slave address of the slave device is stored. bits 7~ 1 of the sima register defne the device slave address. bit 0 is not defned. when a master device, which is connected to the i 2 c bus, sends out an address, which matches the slave address in the sima register, the slave device will be selected. note that the sima register is the same register address as simc2 which is used by the spi interface. bit 0 undefned bit this bit can be read or written by user software program. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 9? ?an?a?? ??? ? 011 rev. 1.00 93 ?an?a?? ??? ? 011 ? ? ? ? ? ?- ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? i 2 c block diagram i 2 c bus communication communication on the i 2 c bus requires four separate steps, a start signal, a slave device address transmission, a data transmission and fnally a stop signal. when a start signal is placed on the i 2 c bus, all devices on the bus will receive this signal and be notifed of the imminent arrival of data on the bus. the frst seven bits of the data will be the slave address with the frst bit being the msb. if the address of the slave device matches that of the transmitted address, the haas bit in the simc1 register will be set and an i 2 c interrupt will be generated. after entering the interrupt service routine, the slave device must first check the condition of the haas bit to determine whether the interrupt source originates from an address match or from the completion of an 8-bit data transfer. during a data transfer, note that after the 7-bit slave address has been transmitted, the following bit, which is the 8th bit, is the read/write bit whose value will be placed in the srw bit. this bit will be checked by the slave device to determine whether to go into transmit or receive mode. before any transfer of data to or from the i 2 c bus, the microcontroller must initialise the bus, the following are steps to achieve this: step 1 set the sim2~sim0 and simen bits in the simc0 register to "1" to enable the i 2 c bus. step 2 write the slave address of the device to the i 2 c bus address register sima. step 3 set the sime and sim muti-function interrupt enable bit of the interrupt control register to enable the sim interrupt and multi-function interrupt. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 9? ?an?a?? ??? ? 011 rev. 1.00 93 ?an?a?? ??? ? 011 ? ? ? ? ? ? - ? ? ? ? ? ?? ? ? ? ? ? - i 2 c bus initialisation flow chart i 2 c bus start signal the start signal can only be generated by the master device connected to the i 2 c bus and not by the slave device. this start signal will be detected by all devices connected to the i 2 c bus. when detected, this indicates that the i 2 c bus is busy and therefore the hbb bit will be set. a start condition occurs when a high to low transition on the sda line takes place when the scl line remains high. slave address the transmission of a start signal by the master will be detected by all devices on the i 2 c bus. to determine which slave device the master wishes to communicate with, the address of the slave device will be sent out immediately following the start signal. all slave devices, after receiving this 7-bit address data, will compare it with their own 7-bit slave address. if the address sent out by the master matches the internal address of the microcontroller slave device, then an internal i 2 c bus interrupt signal will be generated. the next bit following the address, which is the 8th bit, defnes the read/write status and will be saved to the srw bit of the simc1 register. the slave device will then transmit an acknowledge bit, which is a low level, as the 9th bit. the slave device will also set the status fag haas when the addresses match. as an i 2 c bus interrupt can come from two sources, when the program enters the interrupt subroutine, the haas bit should be examined to see whether the interrupt source has come from a matching slave address or from the completion of a data byte transfer. when a slave address is matched, the device must be placed in either the transmit mode and then write data to the simd register, or in the receive mode where it must implement a dummy read from the simd register to release the scl line. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 94 ?an?a?? ??? ? 011 rev. 1.00 95 ?an?a?? ??? ? 011 i 2 c bus read/write signal the srw bit in the simc1 register defnes whether the slave device wishes to read data from the i 2 c bus or write data to the i 2 c bus. the slave device should examine this bit to determine if it is to be a transmitter or a receiver. if the srw fag is "1" then this indicates that the master device wishes to read data from the i 2 c bus, therefore the slave device must be setup to send data to the i 2 c bus as a transmitter. if the srw fag is "0" then this indicates that the master wishes to send data to the i 2 c bus, therefore the slave device must be setup to read data from the i 2 c bus as a receiver. i 2 c bus slave address acknowledge signal after the master has transmitted a calling address, any slave device on the i 2 c bus, whose own in - ternal address matches the calling address, must generate an ac knowledge signal. the acknowledge signal will inform the master that a slave device has accepted its calling address. if no acknowl - edge signal is received by the master then a stop signal must be transmitted by the master to end the communication. when the haas fag is high, the addresses have matched and the slave device must check the srw fag to determine if it is to be a transmitter or a receiver. if the srw fag is high, the slave device should be setup to be a transmitter so the htx bit in the simc1 register should be set to " 1 " . if the srw fag is low, then the microcontroller slave device should be setup as a receiver and the htx bit in the simc1 register should be set to " 0 " . i 2 c bus data and acknowledge signal the transmitted data is 8-bits wide and is transmitted after the slave device has acknowledged receipt of its slave address. the order of serial bit transmission is the msb frst and the lsb last. after receipt of 8-bits of data, the receiver must transmit an acknowledge signal, level " 0 " , before it can receive the next data byte. if the slave transmitter does not receive an acknowledge bit signal from the master receiver, then the slave transmitter will release the sda line to allow the master to send a stop signal to release the i 2 c bus. the corresponding data will be stored in the simd register. if setup as a transmitter, the slave device must frst write the data to be transmitted into the simd register. if setup as a receiver, the slave device must read the transmitted data from the simd register. when the slave receiver receives the data byte, it must generate an acknowledge bit, known as txak, on the 9th clock. the slave device, which is setup as a transmitter will check the rxak bit in the simc1 register to determine if it is to send another data byte, if not then it will release the sda line and await the receipt of a stop signal from the master. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 94 ?an?a?? ??? ? 011 rev. 1.00 95 ?an?a?? ??? ? 011 ? ? ? ? ? ? ? ? - ? - ? ? i 2 c communication timing diagram note: *when a slave address is matched, the device must be placed in either the transmit mode and then write data to the simd register, or in the receive mode where it must implemented a dummy read from the simd register to release the scl line. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 9? ?an?a?? ??? ? 011 rev. 1.00 97 ?an?a?? ??? ? 011 ? ? ? ? i 2 c bus isr flow chart HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 9? ?an?a?? ??? ? 011 rev. 1.00 97 ?an?a?? ??? ? 011 peripheral clock output the peripheral clock output allows the device to supply external hardware with a clock signal synchronised to the microcontroller clock. peripheral clock operation as the peripheral clock output pin, pck, is shared with i/o line, the required pin function is chosen via pcken in the simc0 register. the peripheral clock function is controlled using the simc0 register. the clock source for the peripheral clock output can originate from either the timer/event counter 0 output/2 or a divided ratio of the internal fsys clock. the pcken bit in the simc0 register is the overall on/off control, setting pcken bit to "1" enables the peripheral clock, setting pcken bit to "0" disables it. the required division ratio of the system clock is selected using the pckp1 and pckp0 bits in the same register. simc0 register bit 7 6 5 4 3 2 1 0 name sim? sim1 sim0 pcken pckp1 pckp0 simen r/w r/w r/w r/w r/w r/w r/w r/w por 1 1 1 0 0 0 0 bit 7~5 sim2, sim1, sim0 : sim operating mode control described elsewhere bit 4 pcken : peripheral clock pin control 0: disable 1: enable bit 3~2 pckp1, pckp0 : select pck output pin frequency 00: f sys 01: f sys /4 10: f sys /8 11: timer/event counter 0 output /2 (pfd0) bit 1 simen : sim control described elsewhere bit 0 unimplemented, read as " 0 " HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 98 ?an?a?? ??? ? 011 rev. 1.00 99 ?an?a?? ??? ? 011 spia serial interface C spia the devices contain an independent spia function, known as the spia. it is important not to confuse this independent spia function with the additional one contained within the combined sim function, which is described in another section of this datasheet. the device includes a single spia serial interface. the spia interface is a full duplex serial data link, originally designed by motorola, which allows multiple devices connected to the same spia bus to communicate with each other. the devices communicate using a master/slave technique where only the single master device can initiate a data transfer. a simple four line signal bus is used for all communication and these pins are shared with normal i/o pins. the spia function is selected via a confguration option. spia interface communication four lines are used for spia communication known as sdia - serial data input, sdoa - serial data output, scka - serial clock and scsa - slave select. note that the condition of the slave select line is conditioned by the csen bit in the sbcr control register. if the csen bit is high then the scsa line is active while if the bit is low then the scsa line will be in a foating condition. the following timing diagram depicts the basic timing protocol of the spia bus. spia registers there are two registers associated with the spia interface. these are the sbcr register which is the control register and the sbdr which is the data register. the sbcr register is used to setup the required setup parameters for the spia bus and also used to store associated operating fags, while the sbdr register is used for data storage. after power on, the contents of the sbdr register will be in an unknown condition while the sbcr register will default to the condition below: cks m1 m0 sben mlsa csena wcola trfa 0 1 1 0 0 0 0 0 note that data written to the sbdr register will only be written to the txrx buffer, whereas data read from the sbdr register will actual be read from the register . spia bus enable/disable to enable the spia bus, csen = 1, scsa =0, then wait for data to be written to the sbdr (txrx bufffer) register. for the master mode, after data has been written to the sbdr (txrx buffer) register, then transmission or reception will start automatically. when all the data has been transferred the trf bit should be set. for the slave mode, when clock pulses are received on scka, data in the txrx buffer will be shifted out or data on sdia will be shifted in. to disable the spia bus scka, sdia, sdoa, scsa should be in a foating condition. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 98 ?an?a?? ??? ? 011 rev. 1.00 99 ?an?a?? ??? ? 011 ? ? ? ? ? ? ? ? ? ? ?- ? ? ? ? ? ? ? ? ? ? ? ? ? spia block diagram sbcr register bit 7 6 5 4 3 2 1 0 name cks m1 m0 sben mlsa csena wcola trfa r/w r/w r/w r/w r/w r/w r/w r/w r/w por 0 1 1 0 0 0 0 0 bit 7 cks : spia clock source select bit 0: f spia =f sys /4 1: f spia =f lxt bit 6,5 m1,m0 : master/slave/baud rate bits 00: master, baud rate : f spia 01: master, baud rate : f spia /4 10: master, baud rate : f spia /16 11: slave mode bit 4 sben : serial bus enable/disable bit 0: disable 1: enable dependent upon csen bit bit 3 mlsa : msb/lsb first bit 0: lsb shift frst 1: msb shift frst bit 2 csena : selection signal enable/disable bit 0: scsa foating 1: enable bit 1 wcola : write collision bit 0: collision free 1: collision detected bit 0 trfa : transmit /receive flag 0: not complete 1: transmission/reception complete note: the trf fag will also generate an spia interrupt signal, for more informaton refer to the interrupt section. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 100 ?an?a?? ??? ? 011 rev. 1.00 101 ?an?a?? ??? ? 011 ? ?? ? ?? ? - ?? ? ?? spia bus timing spia operation all communication is carried out using the 4-line interface for both master or slave mode. the timing diagram shows the basic operation of the bus. the csen bit in the sbcr register controls the overall function of the spia interface. setting this bit high, will enable the spia interface by allowing the scsa line to be active, which can then be used to control the spia inteface. if the csen bit is low, the spia interface will be disabled and the scsa line will be in a foating condition and can therefore not be used for control of the spia interface. the sben bit in the sbcr register must also be high which will place the sdia line in a foating condition and the sdoa line high. if in master mode the scka line will be either high or low depending upon the clock polarity confguration option. if in slave mode the scka line will be in a foating condition. if sben is low then the bus will be disabled and scsa , sdia, sdoa and scka will all be in a foating condition. in the master mode the master will always generate the clock signal. the clock and data transmission will be initiated after data has been written to the sbdr register. in the slave mode, the clock signal will be received from an external master device for both data transmission or reception. the following sequences show the order to be followed for data transfer in both master and slave mode: master mode: step 1 select the clock source using the cks bit in the sbcr control register . step 2 setup the m0 and m1 bits in the sbcr control register to select the master mode and the required baud rate. values of 00, 01 or 10 can be selected. step 3 setup the csen bit and setup the mls bit to choose if the data is msb or lsb frst, this must be same as the slave device. step 4 setup the sben bit in the sbcr control register to enable the spia interface. step 5 for write operations: write the data to the sbdr register, which will actually place the data into the txrx buffer. then use the scka and scsa lines to output the data. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 100 ?an?a?? ??? ? 011 rev. 1.00 101 ?an?a?? ??? ? 011 goto to step6. for read operations: the data transferred in on the sdia line will be stored in the txrx buffer until all the data has been received at which point it will be latched into the sbdr register. step 6 check the wcol bit, if set high then a collision error has occurred so return to step5. if equal to zero then go to the following step. step 7 check the trf bit or wait for an sbi serial bus interrupt. step 8 read data from the sbdr register. step 9 clear trf. step10 goto step 5. slave mode: step 1 the cks bit has a don't care value in the slave mode. step 2 setup the m0 and m1 bits to 00 to select the slave mode. the cks bit is don't care. step 3 setup the csen bit and setup the mls bit to choose if the data is msb or lsb frst, this must be same as the master device. step 4 setup the sben bit in the sbcr control register to enable the spia interface. step 5 for write operations: write data to the sbcr register, which will actually place the data into the txrx register, then wait for the master clock and scsa signal. after this goto step 6. for read operations: the data transferred in on the sdia line will be stored in the txrx buffer until all the data has been received at which point it will be latched into the sbdr register . step 6 check the wcol bit, if set high then a collision error has occurred so return to step5. if equal to zero then go to the following step. step 7 check the trf bit or wait for an sbi serial bus interrupt. step 8 read data from the sbdr register. step 9 clear trf step10 goto step 5 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 10? ?an?a?? ??? ? 011 rev. 1.00 103 ?an?a?? ??? ? 011 spia confguration options several confguration options exist for the spia interface function which must be setup during device programming. one option is to enable the operation of the wcol, write collision bit, in the sbcr register. another option exists to select the clock polarity of the scka line. a confguration option also exists to disable or enable the operation of the csen bit in the sbcr register. if the confguration option disables the csen bit then this bit cannot be used to affect overall control of the spia interface. error detection the wcol bit in the sbcr register is provided to indicate errors during data transfer. the bit is set by the serial interface but must be cleared by the application program. this bit indicates a data collision has occurred which happens if a write to the sbdr register takes place during a data transfer operation and will prevent the write operation from continuing. the bit will be set high by the serial interface but has to be cleared by the user application program. the overall function of the wcol bit can be disabled or enabled by a confguration option. programming considerations when the device is placed into the idle mode note that data reception and transmission will continue. the trf bit is used to generate an interrupt when data has been transferred or received. digital to analog converter C dac the devices include a 12-bit digital to analog converter function. this function allows digital data contained in the device to generate audio signals. operation the data to be converted is stored in two registers dal and dah. the dah register stores the highest 8-bits, da4~da11, while dal stores the lowest 4-bits, da0~da3. an bit in the control register, ctrl2, provides overall dac on/off control and a volume control register, vol, provides a 3-bit 8-level volume control. the dac output is channeled to pin aud which is pin- shared with i/o pin pa4. when the dac is enabled by setting the dacen pin high, then the original i/o function will be disabled, along with any pull-high resistor options. the dac output reference voltage is the power supply voltage v dd . dah register bit 7 6 5 4 3 2 1 0 name da11 da10 da9 da8 da7 da? da5 da4 r/w r/w r/w r/w r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 0 bits 7~0 da11~da0 audio output dac high byte bits dal register bit 7 6 5 4 3 2 1 0 name da3 da? da1 da0 r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 0 bits 7~4 da3~da0 audio output dac low bits bits 3~0 unimplemented C read as 0 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 10? ?an?a?? ??? ? 011 rev. 1.00 103 ?an?a?? ??? ? 011 ctrl2 register bit 7 6 5 4 3 2 1 0 name dacen pwmc3 pwmc? lxten r/w r/w r/w r/w r/w por 0 0 0 1 bit 7 dacen : dac disable/enable control 0: disable 1: enable bit 6 unimplemented, read as "0" bit 5 pwmc3 : io or pwm3 control described elsewhere bit 4 pwmc2 : io or pwm2 control described elsewhere bit 3~1 unimplemented, read as "0" bit 0 lxten : lxt oscillator on/off control after execution of halt instruction described elsewhere vol register bit 7 6 5 4 3 2 1 0 name vol? vol1 vol0 r/w r/w r/w r/w r/w por 0 0 0 0 0 0 0 0 bits 7~5 vol2~vol0 audio volume control bits 4~ 0 unimplemented C read as 0 low voltage detector - lvd each device has a low voltage detector function, also known as lvd. this enables the device to monitor the power supply voltage, v dd , and provide a warning signal should it fall below a certain level. this function may be especially useful in battery applications where the supply voltage will gradually reduce as the battery ages, as it allows an early warning battery low signal to be gener - ated. lvd register the low voltage detector is controlled using a single register, lvdc, and confguration options. the voltage threshold level to be detected is determined using a confguration option, therefore cannot be modifed by the application program. a low voltage condition is indicated when the lvdo bit is set. if the lvdo bit is low, this indi - cates that the v dd voltage is above the preset low voltage value. the lvden bit is used to control the overall on/off function of the low voltage detector. setting the bit high will enable the low volt - age detector. clearing the bit to zero will switch off the internal low voltage detector circuits. as the low voltage detector will consume a certain amount of power, it may be desirable to switch off the circuit when not in use, an important consideration in power sensitive battery powered applica - tions. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 104 ?an?a?? ??? ? 011 rev. 1.00 105 ?an?a?? ??? ? 011 lvdc register bit 7 6 5 4 3 2 1 0 name lvdc lvden r/w r r/w por 0 0 bit 7~6 unimple mented, read as "0" bit 5 lvdo : lvd output flag 0: no low voltage detect 1: low voltage detect bit 4 lvden : low voltage detector control 0: disable 1: enable bit 3~0: unimplemented, read as "0" lvd operation the low voltage detector function operates by comparing the power supply voltage, v dd , with a pre-specifed voltage level voltage level setup using a confguration option. when the power sup - ply voltage, v dd , falls below this pre-determined value, the lvdo bit will be set high indicating a low power supply voltage condition. the low voltage detector function is supplied by a reference voltage which will be automatically enabled. when the device is powered down the low voltage detector will remain active if the lvden bit is high. after enabling the low voltage detector, a time delay t lvds should be allowed for the circuitry to stabilise before reading the lvdo bit. note also that as the v dd voltage may rise and fall rather slowly, at the voltage nears that of vlvd, there may be multiple bit lvdo transitions. lvd operation &rqjxudwlrq2swlrqv confguration options refer to certain options within the mcu that are programmed into the otp program memory device during the programming process. during the development process, these options are selected using the ht-ide software development tools. as these options are programmed into the device using the hardware programming tools, once they are selected they can not be changed later by the application software. all options must be defned for proper system function, the details of which are shown in the table. no. options oscillator options 1 high speed s?stem oscillato? selection - f h : 1. hxt ?. erc 3. hirc ? low speed s?stem oscillato? selection - f l : 1. lxt ?. lirc HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 104 ?an?a?? ??? ? 011 rev. 1.00 105 ?an?a?? ??? ? 011 no. options 3 wdt clock selection - f s : 1. lxt ?. lirc 3. f sys /4 4 hirc f?eq?enc? selection: 1. 4mhz ?. 8mhz 3. 1?mhz 5 sst fo ? hirc/erc-tsst: 1. 10?4 clocks ?. ? clocks reset pin options 5 pa7/ res pin options: 1. res pin ?. i/o pin watchdog options ? watchdog time ? f?nction: 1. enable ?. disable 7 clrwdt inst ??ctions selection: 1. 1 inst??ctions ?. ? inst??ctions lvr options 8 lvr f ?nction: 1. enable ?. disable 9 lvr/lvd voltage selection: 1. ?.1v/?.?v ?. 3.15v/3.3v 3. 4.?v/4.4v sim options 10 sim f?nction: 1. enable ?. disable 11 spi - wcol bit: 1. enable ?. disable 1? spi - csen bit: 1. enable ?. disable 13 i ? c debo? nce time selection: 1. no debo?nce ?. 1 s?stem clock debo?nce 3. ? s?stem clock debo?nce 14 i ? c-rnic bit: 1. enable ?. disable 15 spi f?nction: 1. enable ?. disable 1? spi-cpol bit: 1. falling edge ?. rising edge dac options 17 dac f?nction: 1. dac ?. i/o HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 10? ?an?a?? ??? ? 011 rev. 1.00 107 ?an?a?? ??? ? 011 application circuit ? ? note: "*" it is recommended that this component is added for esd protection. "**" it is recommended that this component is added in environments where power line noise is signifcant. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 10? ?an?a?? ??? ? 011 rev. 1.00 107 ?an?a?? ??? ? 011 instruction set introduction central to the successful operation of any microcontroller is its instruction set, which is a set of program instruction codes that directs the microcontroller to perform certain operations. in the case of holtek microcontrollers, a comprehensive and fexible set of over 60 instructions is provided to enable programmers to implement their application with the minimum of programming overheads. for easier understanding of the various instruction codes, they have been subdivided into several functional groupings. instruction timing most instructions are implemented within one instruction cycle. the exceptions to this are branch, call, or table read instructions where two instruction cycles are required. one instruction cycle is equal to 4 system clock cycles, therefore in the case of an 8mhz system oscillator, most instructions would be implemented within 0.5s and branch or call instructions would be implemented within 1s. although instructions which require one more cycle to implement are generally limited to the jmp, call, ret, reti and table read instructions, it is important to realize that any other instructions which involve manipulation of the program counter low register or pcl will also take one more cycle to implement. as instructions which change the contents of the pcl will imply a direct jump to that new address, one more cycle will be required. examples of such instructions would be "clr pcl" or "mov pcl, a". for the case of skip instructions, it must be noted that if the result of the comparison involves a skip operation then this will also take one more cycle, if no skip is involved then only one cycle is required. moving and transferring data the transfer of data within the microcontroller program is one of the most frequently used operations. making use of three kinds of mov instructions, data can be transferred from registers to the accumulator and vice-versa as well as being able to move specifc immediate data directly into the accumulator. one of the most important data transfer applications is to receive data from the input ports and transfer data to the output ports. arithmetic operations the ability to perform certain arithmetic operations and data manipulation is a necessary feature of most microcontroller applications. within the holtek microcontroller instruction set are a range of add and subtract instruction mnemonics to enable the necessary arithmetic to be carried out. care must be taken to ensure correct handling of carry and borrow data when results exceed 255 for addition and less than 0 for subtraction. the increment and decrement instructions inc, inca, dec and deca provide a simple means of increasing or decreasing by a value of one of the values in the destination specifed. logical and rotate operations the standard logical operations such as and, or, xor and cpl all have their own instruction within the holtek microcontroller instruction set. as with the case of most instructions involving data manipulation, data must pass through the accumulator which may involve additional programming steps. in all logical data operations, the zero flag may be set if the result of the operation is zero. another form of logical data manipulation comes from the rotate instructions such as rr, rl, rrc and rlc which provide a simple means of rotating one bit right or left. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 108 ?an?a?? ??? ? 011 rev. 1.00 109 ?an?a?? ??? ? 011 different rotate instructions exist depending on program requirements. rotate instructions are useful for serial port programming applications where data can be rotated from an internal register into the carry bit from where it can be examined and the necessary serial bit set high or low. another application where rotate data operations are used is to implement multiplication and division calculations. branches and control transfer program branching takes the form of either jumps to specifed locations using the jmp instruction or to a subroutine using the call instruction. they differ in the sense that in the case of a subroutine call, the program must return to the instruction immediately when the subroutine has been carried out. this is done by placing a return instruction ret in the subroutine which will cause the program to jump back to the address right after the call instruction. in the case of a jmp instruction, the program simply jumps to the desired location. there is no requirement to jump back to the original jumping off point as in the case of the call instruction. one special and extremely useful set of branch instructions are the conditional branches. here a decision is frst made regarding the condition of a certain data memory or individual bits. depending upon the conditions, the program will continue with the next instruction or skip over it and jump to the following instruction. these instructions are the key to decision making and branching within the program perhaps determined by the condition of certain input switches or by the condition of internal data bits. bit operations the ability to provide single bit operations on data memory is an extremely fexible feature of all holtek microcontrollers. this feature is especially useful for output port bit programming where individual bits or port pins can be directly set high or low us ing either the "set [m].i" or "clr [m]. i" instructions respectively. the feature removes the need for programmers to frst read the 8-bit output port, manipulate the input data to ensure that other bits are not changed and then output the port with the correct new data. this read-modify-write process is taken care of automatically when these bit operation instructions are used. table read operations data storage is normally implemented by using registers. however, when working with large amounts of fxed data, the volume involved often makes it inconvenient to store the fxed data in the data memory. to overcome this problem, holtek microcontrollers allow an area of program memory to be setup as a table where data can be directly stored. a set of easy to use instructions provides the means by which this fxed data can be referenced and retrieved from the program memory. other operations in addition to the above functional instructions, a range of other instructions also exist such as the "halt" instruction for power-down operations and instructions to control the operation of the watchdog timer for reliable program operations under extreme electric or electromagnetic environments. for their relevant operations, refer to the functional related sections. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 108 ?an?a?? ??? ? 011 rev. 1.00 109 ?an?a?? ??? ? 011 instruction set summary the following table depicts a summary of the instruction set categorised according to function and can be consulted as a basic instruction reference using the following listed conventions. table conventions x: bits immediate data m: data memory address a: accumulator i: 0~7 number of bits addr: program memory address mnemonic description cycles flag affected arithmetic add a?[m] add data memo?? to acc 1 z? c? ac? ov addm a?[m] add acc to data memo ?? 1 note z? c? ac? ov add a?x add immediate data to acc 1 z? c? ac? ov adc a?[m] add data memo?? to acc with ca??? 1 z? c? ac? ov adcm a?[m] add acc to data memo ?? with ca??? 1 note z? c? ac? ov sub a?x s?bt?act immediate data f? om the acc 1 z? c? ac? ov sub a?[m] s?bt?act data memo?? f? om acc 1 z? c? ac? ov subm a?[m] s?bt?act data memo?? f? om acc with ?es?lt in data memo?? 1 note z? c? ac? ov sbc a?[m] s?bt?act data memo?? f? om acc with ca??? 1 z? c? ac? ov sbcm a?[m] s?bt?act data memo?? f? om acc with ca ???? ?es?lt in data memo?? 1 note z? c? ac? ov daa [m] decimal adj? st acc fo? addition with ?es?lt in data memo?? 1 note c logic operation and a?[m] logical and data memo ?? to acc 1 z or a?[m] logical or data memo?? to acc 1 z xor a?[m] logical xor data memo?? to acc 1 z andm a?[m] logical and acc to data memo ?? 1 note z orm a?[m] logical or acc to data memo ?? 1 note z xorm a?[m] logical xor acc to data memo ?? 1 note z and a?x logical and immediate data to acc 1 z or a?x logical or immediate data to acc 1 z xor a?x logical xor immediate data to acc 1 z cpl [m] complement data memo?? 1 note z cpla [m] complement data memo?? with ?es? lt in acc 1 z increment & decrement inca [m] inc?ement data memo?? with ?es? lt in acc 1 z inc [m] inc?ement data memo?? 1 note z deca [m] dec?ement data memo?? with ?es? lt in acc 1 z dec [m] dec?ement data memo?? 1 note z rotate rra [m] rotate data memo?? ?ight with ?es? lt in acc 1 none rr [m] rotate data memo?? ?ight 1 note none rrca [m] rotate data memo?? ?ight th?o?gh ca??? with ?es? lt in acc 1 c rrc [m] rotate data memo?? ?ight th?o?gh ca??? 1 note c rla [m] rotate data memo?? left with ?es? lt in acc 1 none rl [m] rotate data memo?? left 1 note none rlca [m] rotate data memo?? left th?o?gh ca??? with ?es? lt in acc 1 c rlc [m] rotate data memo?? left th?o?gh ca??? 1 note c HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 110 ?an?a?? ??? ? 011 rev. 1.00 111 ?an?a?? ??? ? 011 mnemonic description cycles flag affected data move mov a ?[m] move data memo?? to acc 1 none mov [m]?a move acc to data memo ?? 1 note none mov a ?x move immediate data to acc 1 none bit operation clr [m].i clea? bit of data memo?? 1 note none set [m].i set bit of data memo?? 1 note none branch ? mp add? ??mp ?nconditionall? ? none sz [m] skip if data memo?? is ze?o 1 note none sza [m] skip if data memo?? is ze? o with data movement to acc 1 note none sz [m].i skip if bit i of data memo?? is ze?o 1 note none snz [m].i skip if bit i of data memo?? is not ze?o 1 note none siz [m] skip if inc?ement data memo?? is ze?o 1 note none sdz [m] skip if dec?ement data memo?? is ze?o 1 note none siza [m] skip if inc?ement data memo?? is ze?o with ?es? lt in acc 1 note none sdza [m] skip if dec?ement data memo?? is ze?o with ?es? lt in acc 1 note none call add ? s?b?o?tine call ? none ret ret??n f?om s?b?o?tine ? none ret a ?x ret??n f?om s?b?o? tine and load immediate data to acc ? none reti ret??n f?om inte???pt ? none table read tabrdc [m] read table (c??? ent page) to tblh and data memo?? ? note none tabrdl [m] read table (last page) to tblh and data memo ?? ? note none miscellaneous nop no ope?ation 1 none clr [m] clea? data memo?? 1 note none set [m] set data memo?? 1 note none clr wdt clea? watchdog time? 1 to ? pdf clr wdt1 p?e-clea? watchdog time? 1 to ? pdf clr wdt? p?e-clea? watchdog time? 1 to ? pdf swap [m] swap nibbles of data memo?? 1 note none swapa [m] swap nibbles of data memo?? with ?es? lt in acc 1 none halt ente? powe? down mode 1 to ? pdf note: 1. for skip instructions, if the result of the comparison involves a skip then two cycles are required, if no skip takes place only one cycle is required. 2. any instruction which changes the contents of the pcl will also require 2 cycles for execution. 3. for the "clr wdt1" and "clr wdt2" instructions the to and pdf fags may be affected by the execution status. the to and pdf flags are cleared after both "clr wdt1" and "clr wdt2" instructions are consecutively executed. otherwise the to and pdf fags remain unchanged. HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 110 ?an?a?? ??? ? 011 rev. 1.00 111 ?an?a?? ??? ? 011 instruction defnition add data memo?? to acc with ca??? the contents of the specifed data memory, accumulator and the carry fag are added. the ?es?lt is sto? ed in the acc?m?lato? . acc acc + [m] + c ov ? z? ac? c add acc to data memo ?? with ca??? the contents of the specifed data memory, accumulator and the carry fag are added. the result is stored in the specifed data memory. [m] acc + [m] + c ov ? z? ac? c add data memo?? to acc the contents of the specifed data memory and the accumulator are added. the ?es?lt is sto? ed in the acc?m?lato? . acc acc + [m] ov ? z? ac? c add immediate data to acc the contents of the accumulator and the specifed immediate data are added. the ?es?lt is sto? ed in the acc?m?lato? . ac acc + x ov ? z? ac? c add acc to data memo ?? the contents of the specifed data memory and the accumulator are added. the result is stored in the specifed data memory. [m] acc + [m] ov ? z? ac? c logical and data memo ?? to acc data in the accumulator and the specifed data memory perform a bitwise logical and ope? ation. the ?es?lt is sto? ed in the acc?m?lato? . acc acc and [m] z logical and immediate data to acc data in the acc ?m?lato? and the specified immediate data pe?fo? m a bitwise logical and ope ? ation. the ?es?lt is sto? ed in the acc?m?lato? . acc acc and x z logical and acc to data memo ?? data in the specifed data memory and the accumulator perform a bitwise logical and ope? ation. the ?es?lt is sto?ed in the data memo?? . [m] acc and [m] z adc a,[m] desc?iption ope?ation affected fag(s) adcm a,[m] desc?iption ope?ation affected fag(s) add a,[m] desc?iption ope?ation affected fag(s) add a,x desc?iption ope?ation affected fag(s) addm a,[m] desc?iption ope?ation affected fag(s) and a,[m] desc?iption ope?ation affected fag(s) and a,x desc?iption ope?ation affected fag(s) andm a,[m] desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 11 ? ?an?a?? ??? ? 011 rev. 1.00 113 ?an?a?? ??? ? 011 s?b?o?tine call unconditionally calls a subroutine at the specifed address. the program counter then inc ? ements b? 1 to obtain the add ? ess of the next inst ?? ction which is then p? shed onto the stack. the specified add?ess is then loaded and the p?og? am contin ? es exec ? tion f ? om this new add ? ess. as this inst?? ction ? eq ? i ? es an additional ope?ation? it is a two c?cle inst??ction. stack p?og?am co?nte? + 1 p?og?am co?nte? add? none clea? data memo?? each bit of the specifed data memory is cleared to 0. [m] 00h none clea? bit of data memo?? bit i of the specifed data memory is cleared to 0. [m].i 0 none clea? watchdog time? the to, pdf fags and the wdt are all cleared. wdt clea ?ed to 0 pdf 0 to ? pdf p?e-clea? watchdog time? the to, pdf fags and the wdtare all cleared. note that this instruction works in conj? nction with clr wdt? and m? st be exec? ted alte?natel? with clr wdt? to have effect. repetitivel ? exec? ting this inst?? ction witho? t alte?natel? exec?ting clr wdt? will have no effect. wdt clea ?ed to 0 pdf 0 to ? pdf p?e-clea? watchdog time? the to, pdf fags and the wdtare all cleared. note that this instruction works in conj? nction with clr wdt1 and m? st be exec? ted alte?natel? with clr wdt1 to have effect. repetitivel ? exec? ting this inst?? ction witho? t alte?natel? exec?ting wdt clea ?ed to 0 pdf 0 to ? pdf call addr desc?iption ope?ation affected fag(s) clr [m] desc?iption ope?ation affected fag(s) clr [m].i desc?iption ope?ation affected fag(s) clr wdt desc?iption ope?ation affected fag(s) clr wdt1 desc?iption ope?ation affected fag(s) clr wdt2 desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 11 ? ?an?a?? ??? ? 011 rev. 1.00 113 ?an?a?? ??? ? 011 complement data memo?? each bit of the specified data memo ?? is logicall? complemented (1 ' s complement). bits which p ? evio ? sl? contained a 1 a ? e changed to 0 and vice ve?sa. [m] [m] z complement data memo?? with ?es? lt in acc each bit of the specified data memo ?? is logicall? complemented (1 ' s complement). bits which p ? evio ? sl? contained a 1 a ? e changed to 0 and vice ve? sa. the complemented ?es?lt is sto? ed in the acc?m?lato? and the contents of the data memo?? ?emain ?nchanged. acc [m] z decimal-adj? st acc fo? addition with ?es?lt in data memo?? conve? t the contents of the acc?m?lato? val? e to a bcd ( bina?? coded decimal) val?e ?es? lting f?om the p?evio? s addition of two bcd va? iables. if the low nibble is greater than 9 or if ac fag is set, then a value of 6 will be added to the low nibble. othe ? wise the low nibble ?emains ? nchanged. if the high nibble is g?eate? than 9 or if the c fag is set, then a value of 6 will be added to the high nibble. essentiall ?? the decimal conve?sion is pe?fo?med b? adding 00h? 0?h? ?0h o? 66h depending on the accumulator and fag conditions. only the c fag may be affected b ? this inst?? ction which indicates that if the o? iginal bcd s?m is g?eate? than 100? it allows m?ltiple p?ecision decimal addition. [m] acc + 00h o ? [m] acc + 0 ?h o? [m] acc + ?0h o? [m] acc + ??h c dec?ement data memo?? data in the specifed data memory is decremented by 1. [m] [m] C 1 z dec?ement data memo?? with ?es? lt in acc data in the specifed data memory is decremented by 1. the result is stored in the acc ?m?lato? . the contents of the data memo ?? ?emain ?nchanged. acc [m] C 1 z cpl [m] desc?iption ope?ation affected fag(s) cpla [m] desc?iption ope?ation affected fag(s) daa [m] desc?iption ope?ation affected fag(s) dec [m] desc?iption ope?ation affected fag(s) deca [m] desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 114 ?an?a?? ??? ? 011 rev. 1.00 115 ?an?a?? ??? ? 011 ente? powe? down mode this inst??ction stops the p?og?am exec?tion and t?? ns off the s? stem clock. the contents of the data memo ?? and ?egiste?s a?e ? etained. the wdt and p?escale? a? e clea? ed. the powe? down flag pdf is set and the wdt time-o? t flag to is clea?ed. to 0 pdf 0 to ? pdf inc?ement data memo?? data in the specifed data memory is incremented by 1. [m] [m]+1 z inc?ement data memo?? with ?es? lt in acc data in the specifed data memory is incremented by 1. the result is stored in the acc?m?lato? . the contents of the data memo ?? ?emain ?nchanged. acc [m]+1 z ??mp ?nconditionall? the contents of the p ?og? am co?nte? a?e ? eplaced with the specified add? ess. p? og ? am exec? tion then contin ? es f ? om this new add ? ess. as this ?eq ? i ? es the inse? tion of a d?mm? inst??ction while the new add?ess is loaded? it is a two c?cle inst??ction. p?og?am co?nte? add? none move data memo?? to acc the contents of the specifed data memory are copied to the accumulator. acc [m] none move immediate data to acc the immediate data specifed is loaded into the accumulator. acc x none move acc to data memo ?? the contents of the accumulator are copied to the specifed data memory. [m] acc none no ope?ation no ope?ation is pe?fo?med. exec?tion contin?es with the next inst??ction. no ope?ation none halt desc?iption ope?ation affected fag(s) inc [m] desc?iption ope?ation affected fag(s) inca [m] desc?iption ope?ation affected fag(s) jmp addr desc?iption ope?ation affected fag(s) mov a,[m] desc?iption ope?ation affected fag(s) mov a,x desc?iption ope?ation affected fag(s) mov [m],a desc?iption ope?ation affected fag(s) nop desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 114 ?an?a?? ??? ? 011 rev. 1.00 115 ?an?a?? ??? ? 011 logical or data memo?? to acc data in the accumulator and the specifed data memory perform a bitwise logical or ope? ation. the ?es?lt is sto? ed in the acc?m?lato? . acc acc " or " [m] z logical or immediate data to acc data in the acc ?m?lato? and the specified immediate data pe?fo? m a bitwise logical or ope? ation. the ?es?lt is sto? ed in the acc?m?lato? . acc acc " or " x z logical or acc to data memo ?? data in the specifed data memory and the accumulator perform a bitwise logical or ope? ation. the ?es?lt is sto?ed in the data memo?? . [m] acc " or " [m] z ret??n f?om s?b?o?tine the p?og?am co?nte? is ?esto?ed f? om the stack. p?og?am exec?tion contin?es at the ?esto?ed add?ess. p?og?am co?nte? stack none ret??n f?om s?b?o? tine and load immediate data to acc the p?og?am co?nte? is ?esto?ed f? om the stack and the acc?m?lato? loaded with the specifed immediate data. program execution continues at the restored add?ess. p?og?am co?nte? stack acc x none ret??n f?om inte???pt the p?og?am co?nte? is ?esto?ed f? om the stack and the inte???pts a?e ?e-enabled b? setting the emi bit. emi is the maste? inte??? pt global enable bit. if an inte???pt was pending when the reti inst ?? ction is exec?ted? the pending inte???pt ?o?tine will be p?ocessed befo?e ?et??ning to the main p?og?am. p?og?am co?nte? stack emi 1 none rotate data memo?? left the contents of the specified data memo ?? a ? e ? otated left b? 1 bit with bit 7 ?otated into bit 0. [m].(i+1) [m].i; (i = 0~?) [m].0 [m].7 none or a,[m] desc?iption ope?ation affected fag(s) or a,x desc?iption ope?ation affected fag(s) orm a,[m] desc?iption ope?ation affected fag(s) ret desc?iption ope?ation affected fag(s) ret a,x desc?iption ope?ation affected fag(s) reti desc?iption ope?ation affected fag(s) rl [m] desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 11 ? ?an?a?? ??? ? 011 rev. 1.00 117 ?an?a?? ??? ? 011 rotate data memo?? left with ?es? lt in acc the contents of the specified data memo?? a?e ?otated left b? 1 bit with bit 7 ? otated into bit 0. the ?otated ?es?lt is sto? ed in the acc?m?lato? and the contents of the data memo?? ?emain ?nchanged. acc.(i+1) [m].i; (i = 0~?) acc.0 [m].7 none rotate data memo?? left th?o?gh ca??? the contents of the specifed data memory and the carry fag are rotated left by 1 bit. bit 7 replaces the carry bit and the original carry fag is rotated into bit 0. [m].(i+1) [m].i; (i = 0~?) [m].0 c c [m].7 c rotate data memo?? left th?o?gh ca??? with ?es? lt in acc data in the specifed data memory and the carry fag are rotated left by 1 bit. bit 7 replaces the carry bit and the original carry fag is rotated into the bit 0. the ?otated ?es?lt is sto? ed in the acc?m?lato? and the contents of the data memo?? ?emain ?nchanged. acc.(i+1) [m].i; (i = 0~?) acc.0 c c [m].7 c rotate data memo?? ?ight the contents of the specifed data memory are rotated right by 1 bit with bit 0 ?otated into bit 7. [m].i [m].(i+1); (i = 0~?) [m].7 [m].0 none rotate data memo?? ?ight with ?es? lt in acc data in the specifed data memory and the carry fag are rotated right by 1 bit with bit 0 ? otated into bit 7. the ?otated ?es?lt is sto? ed in the acc?m?lato ? and the contents of the data memo?? ?emain ?nchanged. acc.i [m].(i+1); (i = 0~?) acc.7 [m].0 none rotate data memo?? ?ight th?o?gh ca??? the contents of the specifed data memory and the carry fag are rotated right by 1 bit. bit 0 replaces the carry bit and the original carry fag is rotated into bit 7. [m].i [m].(i+1); (i = 0~?) [m].7 c c [m].0 c rla [m] desc?iption ope?ation affected fag(s) rlc [m] desc?iption ope?ation affected fag(s) rlca [m] desc?iption ope?ation affected fag(s) rr [m] desc?iption ope?ation affected fag(s) rra [m] desc?iption ope?ation affected fag(s) rrc [m] desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 11 ? ?an?a?? ??? ? 011 rev. 1.00 117 ?an?a?? ??? ? 011 rotate data memo?? ?ight th?o?gh ca??? with ?es? lt in acc data in the specifed data memory and the carry fag are rotated right by 1 bit. bit 0 replaces the carry bit and the original carry fag is rotated into bit 7. the rotated ?es?lt is sto? ed in the acc?m?lato? and the contents of the data memo?? ? emain ?nchanged. acc.i [m].(i+1); (i = 0~?) acc.7 c c [m].0 c s?bt?act data memo?? f? om acc with ca??? the contents of the specifed data memory and the complement of the carry fag a?e s?bt?acted f? om the acc?m?lato? . the ?es?lt is sto? ed in the acc?m?lato? . note that if the result of subtraction is negative, the c fag will be cleared to 0, otherwise if the result is positive or zero, the c fag will be set to 1. acc acc C [m] C c ov ? z? ac? c s?bt?act data memo?? f? om acc with ca??? and ?es?lt in data memo?? the contents of the specifed data memory and the complement of the carry fag a?e s?bt? acted f? om the acc?m?lato? . the ?es? lt is sto? ed in the data memo?? . note that if the result of subtraction is negative, the c fag will be cleared to 0, otherwise if the result is positive or zero, the c fag will be set to 1. acc acc C [m] C c ov ? z? ac? c skip if dec?ement data memo?? is 0 the contents of the specifed data memory are frst decremented by 1. if the result is 0 the following inst ?? ction is skipped. as this ?eq?i? es the inse? tion of a d?mm? inst??ction while the next inst??ction is fetched? it is a two c?cle inst?? ction. if the ?es?lt is not 0 the p?og?am p?oceeds with the following inst??ction. [m] [m] C 1 skip if [m] = 0 none skip if dec?ement data memo?? is ze?o with ?es? lt in acc the contents of the specifed data memory are frst decremented by 1. if the result is 0? the following inst?? ction is skipped. the ?es? lt is sto? ed in the acc?m?lato? but the specifed data memory contents remain unchanged. as this requires the inse? tion of a d?mm? inst?? ction while the next inst?? ction is fetched? it is a two c? cle inst?? ction. if the ? es? lt is not 0? the p ?og ?am p? oceeds with the following inst??ction. acc [m] C 1 skip if acc = 0 none rrca [m] desc?iption ope?ation affected fag(s) sbc a,[m] desc?iption ope?ation affected fag(s) sbcm a,[m] desc?iption ope?ation affected fag(s) sdz [m] desc?iption ope?ation affected fag(s) sdza [m] desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 118 ?an?a?? ??? ? 011 rev. 1.00 119 ?an?a?? ??? ? 011 set data memo?? each bit of the specifed data memory is set to 1. [m] ffh none set bit of data memo?? bit i of the specifed data memory is set to 1. [m].1 1 none skip if inc?ement data memo?? is 0 the contents of the specifed data memory are frst incremented by 1. if the result is 0? the following inst?? ction is skipped. as this ?eq?i? es the inse? tion of a d?mm? inst?? ction while the next inst?? ction is fetched? it is a two c?cle inst?? ction. if the ?es?lt is not 0 the p?og?am p?oceeds with the following inst??ction. [m] [m] + 1 skip if [m] = 0 none skip if inc?ement data memo?? is ze?o with ?es? lt in acc the contents of the specifed data memory are frst incremented by 1. if the result is 0? the following inst?? ction is skipped. the ?es?lt is sto? ed in the acc?m?lato? but the specifed data memory contents remain unchanged. as this requires the inse? tion of a d?mm? inst?? ction while the next inst?? ction is fetched? it is a two c?cle inst?? ction. if the ?es? lt is not 0 the p?og?am p? oceeds with the following inst??ction. acc [m] + 1 skip if acc = 0 none skip if bit i of data memo?? is not 0 if bit i of the specifed data memory is not 0, the following instruction is skipped. as this ?eq?i?es the inse?tion of a d?mm? inst??ction while the next inst??ction is fetched? it is a two c? cle inst?? ction. if the ?es? lt is 0 the p?og? am p? oceeds with the following inst??ction. skip if [m].i 0 none s?bt?act data memo?? f? om acc the specifed data memory is subtracted from the contents of the accumulator. the ? es? lt is sto ? ed in the acc?m? lato ? . note that if the ? es? lt of s? bt ? action is negative, the c fag will be cleared to 0, otherwise if the result is positive or zero, the c fag will be set to 1. acc acc C [m] ov ? z? ac? c set [m] desc?iption ope?ation affected fag(s) set [m].i desc?iption ope?ation affected fag(s) siz [m] desc?iption ope?ation affected fag(s) siza [m] desc?iption ope?ation affected fag(s) snz [m].i desc?iption ope?ation affected fag(s) sub a,[m] desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 118 ?an?a?? ??? ? 011 rev. 1.00 119 ?an?a?? ??? ? 011 s?bt?act data memo?? f? om acc with ?es?lt in data memo?? the specifed data memory is subtracted from the contents of the accumulator. the ?es?lt is sto? ed in the data memo?? . note that if the ?es?lt of s?bt? action is negative, the c fag will be cleared to 0, otherwise if the result is positive or zero, the c fag will be set to 1. [m] acc C [m] ov ? z? ac? c s?bt?act immediate data f? om acc the immediate data specifed by the code is subtracted from the contents of the acc ?m ? lato? . the ?es ? lt is sto? ed in the acc?m? lato? . note that if the ?es ? lt of subtraction is negative, the c fag will be cleared to 0, otherwise if the result is positive or zero, the c fag will be set to 1. acc acc C x ov ? z? ac? c swap nibbles of data memo?? the low-o ?de? and high-o?de? nibbles of the specified data memo?? a? e inte?changed. [m].3~[m].0?[m].7 ~ [m].4 none swap nibbles of data memo?? with ?es? lt in acc the low-o ?de? and high-o?de? nibbles of the specified data memo?? a? e inte ? changed. the ?es? lt is sto? ed in the acc?m?lato? . the contents of the data memo?? ?emain ?nchanged. acc.3 ~ acc.0 [m].7 ~ [m].4 acc.7 ~ acc.4 [m].3 ~ [m].0 none skip if data memo?? is 0 if the contents of the specified data memo ?? is 0? the following inst ?? ction is skipped. as this ?eq?i?es the inse?tion of a d?mm? inst?? ction while the next inst??ction is fetched? it is a two c?cle inst??ction. if the ?es?lt is not 0 the p?og?am p?oceeds with the following inst??ction. skip if [m] = 0 none skip if data memo?? is 0 with data movement to acc the contents of the specifed data memory are copied to the accumulator. if the val? e is ze?o? the following inst?? ction is skipped. as this ?eq?i? es the inse? tion of a d?mm? inst?? ction while the next inst?? ction is fetched? it is a two c?cle inst??ction. if the ?es?lt is not 0 the p?og?am p?oceeds with the following inst??ction. acc [m] skip if [m] = 0 none subm a,[m] desc?iption ope?ation affected fag(s) sub a,x desc?iption ope?ation affected fag(s) swap [m] desc?iption ope?ation affected fag(s) swapa [m] desc?iption ope?ation affected fag(s) sz [m] desc?iption ope?ation affected fag(s) sza [m] desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?0 ?an?a?? ??? ? 011 rev. 1.00 1?1 ?an?a?? ??? ? 011 skip if bit i of data memo?? is 0 if bit i of the specifed data memory is 0, the following instruction is skipped. as this ?eq?i? es the inse? tion of a d?mm? inst ?? ction while the next inst ?? ction is fetched? it is a two c?cle inst??ction. if the ?es?lt is not 0? the p?og?am p? oceeds with the following inst??ction. skip if [m].i = 0 none read table (c??? ent page) to tblh and data memo?? the low b?te of the p?og?am code (c???ent page) add?essed b? the table pointe? (tblp) is moved to the specifed data memory and the high byte moved to tblh. [m] p?og?am code (low b?te) tblh p?og?am code (high b?te) none read table (last page) to tblh and data memo ?? the low b ? te of the p ? og? am code (last page) add ? essed b ? the table pointe ? (tblp) is moved to the specifed data memory and the high byte moved to tblh. [m] p?og?am code (low b?te) tblh p?og?am code (high b?te) none logical xor data memo?? to acc data in the accumulator and the specifed data memory perform a bitwise logical xor ope? ation. the ?es?lt is sto? ed in the acc?m?lato? . acc acc " xor " [m] z logical xor acc to data memo ?? data in the specifed data memory and the accumulator perform a bitwise logical xor ope? ation. the ?es?lt is sto?ed in the data memo?? . [m] acc " xor " [m] z logical xor immediate data to acc data in the acc ?m?lato? and the specified immediate data pe?fo? m a bitwise logical xor ope? ation. the ?es?lt is sto? ed in the acc?m?lato? . acc acc " xor " x z sz [m].i desc?iption ope?ation affected fag(s) tabrdc [m] desc?iption ope?ation affected fag(s) tabrdl [m] desc?iption ope?ation affected fag(s) xor a,[m] desc?iption ope?ation affected fag(s) xorm a,[m] desc?iption ope?ation affected fag(s) xor a,x desc?iption ope?ation affected fag(s) HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?0 ?an?a?? ??? ? 011 rev. 1.00 1?1 ?an?a?? ??? ? 011 package information 28-pin skdip (300mil) outline dimensions symbol dimensions in inch min. nom. max. a 1.375 D 1.395 b 0.?78 D 0.?98 c 0.1?5 D 0.135 d 0.1?5 D 0.145 e 0.01? D 0.0?0 f 0.050 D 0.070 g D 0.100 D h 0.?95 D 0.315 i D 0.375 D symbol dimensions in mm min. nom. max. a 34.93 D 35.43 b 7.0? D 7.57 c 3.18 D 3.43 d 3.18 D 3.?8 e 0.41 D 0.51 f 1.?7 D 1.78 g D ?.54 D h 7.49 D 8.00 i D 9.53 D HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?? ?an?a?? ??? ? 011 rev. 1.00 1?3 ?an?a?? ??? ? 011 28-pin sop (300mil) outline dimensions ms-013 symbol dimensions in inch min. nom. max. a 0.393 D 0.419 b 0.?5? D 0.300 c 0.01? D 0.0?0 c 0.?97 D 0.713 d D D 0.104 e D 0.050 D f 0.004 D 0.01? g 0.01? D 0.050 h 0.008 D 0.013 0 D 8 symbol dimensions in mm min. nom. max. a 9.98 D 10.?4 b ?.50 D 7.?? c 0.30 D 0.51 c 17.70 D 18.11 d D D ?.?4 e D 1.?7 D f 0.10 D 0.30 g 0.41 D 1.?7 h 0.?0 D 0.33 0 D 8 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?? ?an?a?? ??? ? 011 rev. 1.00 1?3 ?an?a?? ??? ? 011 28-pin ssop (150mil) outline dimensions symbol dimensions in inch min. nom. max. a 0.??8 D 0.?44 b 0.150 D 0.157 c 0.008 D 0.01? c 0.38? D 0.394 d 0.054 D 0.0?0 e D 0.0?5 D f 0.004 D 0.010 g 0.0?? D 0.0?8 h 0.007 D 0.010 0 D 8 symbol dimensions in mm min. nom. max. a 5.79 D ?.?0 b 3.81 D 3.99 c 0.?0 D 0.30 c 9.80 D 10.01 d 1.37 D 1.5? e D 0.?4 D f 0.10 D 0.?5 g 0.5? D 0.71 h 0.18 D 0.?5 0 D 8 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?4 ?an?a?? ??? ? 011 rev. 1.00 1?5 ?an?a?? ??? ? 011 44-pin qfp (10mmx10mm) outline dimensions symbol dimensions in inch min. nom. max. a 0.51? D 0.5?8 b 0.390 D 0.398 c 0.51? D 0.5?8 d 0.390 D 0.398 e D 0.031 D f D 0.01? D g 0.075 D 0.087 h D D 0.10? i 0.010 D 0.0?0 ? 0.0?9 D 0.037 k 0.004 D 0.008 l D 0.004 D 0 D 7 symbol dimensions in mm min. nom. max. a 13.00 D 13.40 b 9.90 D 10.10 c 13.00 D 13.40 d 9.90 D 10.10 e D 0.80 D f D 0.30 D g 1.90 D ?.?0 h D D ?.70 i 0.?5 D 0.50 ? 0.73 D 0.93 k 0.10 D 0.?0 l D 0.10 D 0 D 7 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?4 ?an?a?? ??? ? 011 rev. 1.00 1?5 ?an?a?? ??? ? 011 52-pin qfp (14mmx14mm) outline dimensions symbol dimensions in inch min. nom. max. a 0.?81 D 0.?89 b 0.547 D 0.555 c 0.?81 D 0.?89 d 0.547 D 0.555 e D 0.039 D f D 0.01? D g 0.098 D 0.1?? h D D 0.134 i D 0.004 D ? 0.0?9 D 0.041 k 0.004 D 0.008 0 D 7 symbol dimensions in mm min. nom. max. a 17.30 D 17.50 b 13.90 D 14.10 c 17.30 D 17.50 d 13.90 D 14.10 e D 1.00 D f D 0.40 D g ?.50 D 3.10 h D D 3.40 i D 0.10 D ? 0.73 D 1.03 k 0.10 D 0.?0 0 D 7 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?? ?an?a?? ??? ? 011 rev. 1.00 1?7 ?an?a?? ??? ? 011 64-pin lqfp (7mmx7mm) outline dimensions symbol dimensions in inch min. nom. max. a 0.350 D 0.358 b 0.?7? D 0.?80 c 0.350 D 0.358 d 0.?7? D 0.?80 e D 0.01? D f 0.005 D 0.009 g 0.053 D 0.057 h D D 0.0?3 i 0.00? D 0.00? ? 0.018 D 0.030 k 0.004 D 0.008 0 D 7 symbol dimensions in mm min. nom. max. a 8.90 D 9.10 b ?.90 D 7.10 c 8.90 D 9.10 d ?.90 D 7.10 e D 0.40 D f 0.13 D 0.?3 g 1.35 D 1.45 h D D 1.?0 i 0.05 D 0.15 ? 0.45 D 0.75 k 0.09 D 0.?0 0 D 7 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?? ?an?a?? ??? ? 011 rev. 1.00 1?7 ?an?a?? ??? ? 011 reel dimensions product tape and reel specifications reel dimensions sop 28w (300mil) symbol description dimensions in mm a reel outer diameter 330.0 1.0 b reel inner diameter 100.0 1.5 c spindle hole diameter 13.0 +0.5/-0.2 d key slit width 2.0 0.5 t1 space between flange 24.8 +0.3/-0.2 t2 reel thickness 30.2 0.2 package information 2 april 1, 2010 sop 28w (300mil) symbol description dimensions in mm a reel o?te? diamete? 330.01.0 b reel inne? diamete? 100.01.5 c spindle hole diamete? 13.0 +0.5/-0.? d ke? slit width ?.00.5 t1 space between flange ?4.8 +0.3/-0.? t? reel thickness 30.?0.? ssop 28s (150mil) symbol description dimensions in mm a reel o?te? diamete? 330.01.0 b reel inne? diamete? 100.01.5 c spindle hole diamete? 13.0 +0.5/-0.? d ke? slit width ?.00.5 t1 space between flange 1?.8 +0.3/-0.? t? reel thickness ??.?0.? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?8 ?an?a?? ??? ? 011 rev. 1.00 1?9 ?an?a?? ??? ? 011 carrier tape dimensions carrier tape dimensions sop 28w (300mil) symbol description dimensions in mm w carrier tape width 24.0 0.3 p cavity pitch 12.0 0.1 e perforation position 1.75 0.10 f cavity to perforation (width direction) 11.5 0.1 d perforation diameter 1.5 +0.1/-0.0 d1 cavity hole diameter 1.50 +0.25/-0.00 p0 perforation pitch 4.0 0.1 p1 cavity to perforation (length direction) 2.0 0.1 a0 cavity length 10.85 0.10 b0 cavity width 18.34 0.10 k0 cavity depth 2.97 0.10 t carrier tape thickness 0.35 0.01 c cover tape width 21.3 0.1 package information 3 april 1, 2010 sop 28w (300mil) symbol description dimensions in mm w ca??ie? tape width ?4.00.3 p cavit? pitch 1?.00.1 e pe?fo?ation position 1.750.10 f cavit? to pe?fo?ation (width di?ection) 11.50.1 d pe?fo?ation diamete? 1.5 +0.1/-0.0 d1 cavit? hole diamete? 1.50 +0.?5/-0.00 p0 pe?fo?ation pitch 4.00.1 p1 cavit? to pe?fo?ation (length di?ection) ?.00.1 a0 cavit? length 10.850.10 b0 cavit? width 18.340.10 k0 cavit? depth ?.970.10 t ca??ie? tape thickness 0.350.01 c cove? tape width ?1.30.1 ssop 28s (150mil) symbol description dimensions in mm w ca??ie? tape width 1?.00.3 p cavit? pitch 8.00.1 e pe?fo?ation position 1.750.1 f cavit? to pe?fo?ation (width di?ection) 7.50.1 d pe?fo?ation diamete? 1.55 +0.10/-0.00 d1 cavit? hole diamete? 1.50 +0.?5/-0.00 p0 pe?fo?ation pitch 4.00.1 p1 cavit? to pe?fo?ation (length di?ection) ?.00.1 a0 cavit? length ?.50.1 b0 cavit? width 10.30.1 k0 cavit? depth ?.10.1 t ca??ie? tape thickness 0.300.05 c cove? tape width 13.30.1 HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? HT46R068B/ht46r069b enhanced a/d type 8-bit otp mcu p?elimina?? rev. 1.00 1?8 ?an?a?? ??? ? 011 rev. 1.00 1?9 ?an?a?? ??? ? 011 holtek semiconductor inc. (headquarters) no.3? c?eation rd. ii? science pa?k? hsinch?? taiwan tel: 88 ?-3-5?3-1999 fax: 88?-3-5? 3-1189 http://www.holtek.com.tw holtek semiconductor inc. (taipei sales offce) 4f-?? no. 3-?? y ?anq? st.? nankang softwa?e pa?k? taipei 115? taiwan tel: 88 ?-?-??55-7070 fax: 88?-?-??55-7373 fax: 88?-?-??55-7383 (inte?national sales hotline) holtek semiconductor inc. (shenzhen sales offce) 5f ? unit a? p?od?ctivit? b?ilding? no.5 gaoxin m ?nd road? nanshan dist?ict? shenzhen? china 518057 tel: 8 ?-755-8?1?-9908? 8?-755-8?1?-9308 fax: 8?-755-8?1?-97?? holtek semiconductor (usa), inc. (north america sales offce) 4?7?9 f?emont blvd.? f?emont? ca 94538? usa tel: 1-510- ?5?-9880 fax: 1-510-?5?-9885 http://www.holtek.com cop??ight ? ? 011 b? holtek semiconductor inc. the info?mation appea? ing in this data sheet is believed to be acc?? ate at the time of p? blication. howeve ?? holtek ass ?mes no ?esponsibilit ? a? ising f ? om the ? se of the specifications desc? ibed. the applications mentioned he ? ein a?e ? sed solel? fo? the p?? pose of ill?st? ation and holtek makes no wa??ant? o? representation that such applications will be suitable without further modifcation, nor recommends the use of its p ?od? cts fo? application that ma? p?esent a ? isk to h?man life d? e to malf?nction o? othe?wise. holtek's p?od?cts a?e not a?tho? ized fo? ?se as c?itical components in life s?ppo?t devices o? s?stems. holtek ?ese?ves the right to alter its products without prior notifcation. for the most up-to-date information, please visit our web site at http://www.holtek.com.tw . |
Price & Availability of HT46R068B
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |